IMPORTANT: Your tractor is equipped with a 12 volt system. The other vehicle must also be a 12 volt system. Do not use your tractor battery to start other vehicles.

TO ATTACH JUMPER CABLES -

1.Connect one end of the RED cable to the POSITIVE (+) terminal of each battery(A-B), taking care not to short against tractor chassis.

2.Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

3.Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER

1.BLACK cable first from chassis and then from the fully charged battery.

2.RED cable last from both batteries.

02614

Weak or Dead

Fully Charged

Battery

Battery

REPLACING BATTERY

WARNING: Do not short battery termi- nals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc. Positive terminal must be connected first to prevent sparking from accidental grounding.

1.Lift hood to raised position.

2.Remove terminal guard.

3.Disconnect BLACK battery cable then RED battery cable and carefully remove battery from tractor.

4.Install new battery with terminals in same position as old battery.

5.Reinstall terminal guard.

6.First connect RED battery cable to posi- tive (+) battery terminal with hex bolt and keps nut as shown. Tighten securely.

7.Connect BLACK grounding cable to neg- ative (-) battery terminal with remaining hex bolt and keps nut. Tighten securely

8.Close terminal access doors.

9.Close hood.

TO REPLACE HEADLIGHT BULB

1.Raise hood.

2.Pull bulb holder out of the hole in the backside of the grill.

3.Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

4.Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL AS- SEMBLY

1.Raise hood.

2.Unsnap headlight wire connector.

3.Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

4.When replacing hood, be sure to re- connect the headlight wire connector.

Hood

Headlight Wire

Connector

02141

ENGINE

TO ADJUST THROTTLE CONTROL CABLE

The throttle control has been preset at the factory and adjustment should not be nec- essary. Check adjustment as described below before loosening cable. If adjust- ment is necessary, see engine manual

Terminal

Access

Door

Keps Nut

Hex Bolt

Positive (Red)

TO ADJUST CARBURETOR

The carburetor has been preset at the factory and adjustment should not be nec- essary. However, minor adjustment may be required to compensate for differences

Terminal Guard

Cable

Negative (Black) Cable

in fuel, temperature, altitude or load. If the carburetor does need adjustment, see engine manual.

24

Page 24
Image 24
Poulan 193282 manual To Adjust Carburetor

193282 specifications

The Poulan 193282 is a remarkable chainsaw designed for both amateur and professional users who seek reliability, efficiency, and ease of use. This powerful tool stands out in the market for its combination of features and innovative technologies, making it a popular choice for pruning, cutting firewood, and tackling larger tree jobs.

One of the main features of the Poulan 193282 is its robust 42cc engine, which provides ample power to handle a variety of cutting tasks. This engine is designed with a lightweight construction, allowing for improved maneuverability and reduced fatigue during extended use. The chainsaw's fuel-efficient engine not only cuts down on operational costs but also reduces environmental impact, making it an eco-friendly choice for users concerned about their carbon footprint.

Integration of advanced technologies sets the Poulan 193282 apart from its competitors. It features an automatic oiling system that ensures consistent lubrication of the bar and chain, prolonging the lifespan of the tool and enhancing cutting performance. The chainsaw is equipped with a Smart Start system, which allows for easier pull starts, significantly reducing the effort required to start the engine. This is especially beneficial for novice users who may struggle with traditional starting mechanisms.

The Poulan 193282 also boasts a durable 18-inch cutting bar, which is optimized for both efficiency and precision, making it ideal for a variety of cutting applications. The chainsaw’s chain is designed for quick and tool-less adjustments, allowing users to maintain optimal tension easily and keep it in peak operating condition.

Additionally, the ergonomic design of the Poulan 193282 features a comfortable grip handle, which enhances user control and reduces vibration during operation. This focus on user comfort is further reflected in the chainsaw’s lightweight construction, allowing for greater flexibility and ease of handling, essential for precision cutting.

In terms of safety features, the Poulan 193282 includes a chain brake system that instantly stops the chain in case of kickback, providing an additional layer of protection for the user. The inclusion of a transparent fuel tank facilitates easy monitoring of fuel levels, ensuring that you are never caught off guard during a cutting task.

In summary, the Poulan 193282 is a well-rounded chainsaw that combines power, efficiency, and user-friendly features. Its innovative design and advanced technologies make it an excellent choice for those looking to tackle a wide range of cutting tasks with confidence. Whether you are a seasoned professional or a DIY enthusiast, the Poulan 193282 is equipped to meet your needs, delivering performance that stands the test of time.