4.Install belt through stationary idler and clutching idler.

5.Reinstall clutch locator and tighten nut securely.

6.Reconnect clutch harness.

7.Make sure belt is in all pulley grooves and inside all belt guides and keepers.

8.Install mower (See “TO INSTALL MOWER” in this section of manual).

Electric

Clutch Clutch

Locator

Clutching

Idler

Stationary

Idler

Center Span

 

Keeper

Clutch

Transmission

Wire

Harness

Input Pulley

 

01511

TRANSAXLE MOTION CONTROL LE- VER NEUTRAL ADJUSTMENT

The motion control lever has been preset at the factory and adjustment should not be necessary.

1.Loosen adjustment bolt in front of the right rear wheel, and lightly tighten.

2.Start engine and move motion con- trol lever until tractor does not move forward or backward.

3.Hold motion control lever in that posi- tion and turn engine off.

4.While holding motion control lever in place, loosen the adjustment bolt.

5.Move motion control lever to the neu- tral (N) (lock gate) position.

6.Tighten adjustment bolt securely. NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

After above adjustment is made, if the tractor still creeps forward or backward while motion control lever is in neutral position, follow these steps:

1.Loosen the adjustment bolt.

2.Move the motion control lever 1/4 to 1/2 inch in the direction it is trying to creep.

3.Tighten adjustment bolt securely.

4.Start engine and test.

5.If tractor still creeps, repeat above steps until satisfied.

Motion Control Lever

02239

Neutral

Lock

Adjustment Bolt

 

Gate

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not

horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble with crossbars horizontal. Tighten securely.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS

1.Block up axle securely.

2.Remove axle cover, retaining ring and washers to allow wheel removal (rear wheels have a square key - Do not lose).

3.Repair tire and reassemble.

NOTE: On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

4.Replace washers and snap retaining ring securely in axle groove.

5.Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

Retaining Washers

Ring

Axle

 

Cover

 

Square Key

00663

(Rear Wheel Only)

 

TO START ENGINE WITH A WEAK BATTERY

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from bat- teries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the MAINTENANCE section of this manual). If “jumper cables” are used for emergency starting, follow this procedure:

23

Page 23
Image 23
Poulan 193282 manual Transaxle Motion Control LE- VER Neutral Adjustment, To Adjust Steering Wheel ALIGN- Ment

193282 specifications

The Poulan 193282 is a remarkable chainsaw designed for both amateur and professional users who seek reliability, efficiency, and ease of use. This powerful tool stands out in the market for its combination of features and innovative technologies, making it a popular choice for pruning, cutting firewood, and tackling larger tree jobs.

One of the main features of the Poulan 193282 is its robust 42cc engine, which provides ample power to handle a variety of cutting tasks. This engine is designed with a lightweight construction, allowing for improved maneuverability and reduced fatigue during extended use. The chainsaw's fuel-efficient engine not only cuts down on operational costs but also reduces environmental impact, making it an eco-friendly choice for users concerned about their carbon footprint.

Integration of advanced technologies sets the Poulan 193282 apart from its competitors. It features an automatic oiling system that ensures consistent lubrication of the bar and chain, prolonging the lifespan of the tool and enhancing cutting performance. The chainsaw is equipped with a Smart Start system, which allows for easier pull starts, significantly reducing the effort required to start the engine. This is especially beneficial for novice users who may struggle with traditional starting mechanisms.

The Poulan 193282 also boasts a durable 18-inch cutting bar, which is optimized for both efficiency and precision, making it ideal for a variety of cutting applications. The chainsaw’s chain is designed for quick and tool-less adjustments, allowing users to maintain optimal tension easily and keep it in peak operating condition.

Additionally, the ergonomic design of the Poulan 193282 features a comfortable grip handle, which enhances user control and reduces vibration during operation. This focus on user comfort is further reflected in the chainsaw’s lightweight construction, allowing for greater flexibility and ease of handling, essential for precision cutting.

In terms of safety features, the Poulan 193282 includes a chain brake system that instantly stops the chain in case of kickback, providing an additional layer of protection for the user. The inclusion of a transparent fuel tank facilitates easy monitoring of fuel levels, ensuring that you are never caught off guard during a cutting task.

In summary, the Poulan 193282 is a well-rounded chainsaw that combines power, efficiency, and user-friendly features. Its innovative design and advanced technologies make it an excellent choice for those looking to tackle a wide range of cutting tasks with confidence. Whether you are a seasoned professional or a DIY enthusiast, the Poulan 193282 is equipped to meet your needs, delivering performance that stands the test of time.