MAINTENANCE

AUGER GEAR CASE

•The gear case was filled with lubricant to the proper level at the factory. The only time the lubricant needs attention is if service has been performed on the gear case.

•If lubricant is required, use only Ronex ED #1 grease.

TRACTION DRIVE SYSTEM

DO NOT lubricate the drive components inside the snow thrower. The sprockets, hex shafts, drive disc and friction wheel require no lubrication. The bearings and bushings are lifetime lubricated and require no maintenance.

CAUTION: Any lubricating of the above compo- nents can cause contamination of the friction wheel and damage to the drive system of your snow thrower.

ENGINE

See engine manual.

LUBRICATION

Use only high quality detergent oil rated with API service classification SG–SL. Select the oil's SAE viscosity grade according to your expected operating temperature.

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°F. Check your engine oil level more frequently to avoid possible engine damage from running low on oil.

Changetheoilafterevery25hoursofoperationoratleastonce a year if the snow thrower is not used for 25 hours in one year.

Check the crankcase oil level before starting the engine and after each five (5) hours of continuous use. Tighten oil fill cap / dipstick securely each time you check the oil level.

TO CHANGE ENGINE OIL

Determine temperature range anticipated before next oil change. All oil must meet API service classification SG–SL.

•Be sure snow thrower is on level surface.

•Oil will drain more freely when warm.

•Catch oil in a suitable container.

NOTE: The left side wheel may be removed from snow thrower for easier access to the oil drain plug and place- ment of a suitable container. The unit tilted, resting on the frame with the left wheel removed, will help drain any oil trapped inside the engine. (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

1.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with plug.

2.Clean area around drain plug.

3.Remove drain plug and drain oil in a suitable container.

4.Install drain plug and tighten securely.

5.Wipe off any spilled oil from snow thrower and engine.

6.Install left wheel (if removed for draining oil). Be sure to install klick pin into proper hole in wheel axle (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

7.Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine.

8.Refill engine with oil through oil dipstick tube. Pour slowly. Do not overfill. For approximate capacity see “PRODUCT SPECIFICATIONS” section of this manual.

9.Use gauge on oil fill cap/dipstick for checking level. Be sure dipstick cap is tightened securely for accurate reading. Keep oil at “FULL” line on dipstick.

10.Wipe off any spilled oil.

MUFFLER

Inspect and replace corroded muffler as it could create a fire hazard and/or damage.

SPARK PLUG

Replace spark plug at the beginning of each season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in the “PRODUCT SPECIFICATIONS” section of this manual.

CLEANING

IMPORTANT: For best performance, keep snow thrower housing free of any dirt or trash. Clean the outside of your snow thrower after each use.

WARNING: Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with plug.

•Keep finished surfaces/wheels free of gasoline, oil, etc.

•We do not recommend using a garden hose to clean your snow thrower unless the electrical system, muffler and carburetor are covered to keep water out. Water in engine can result in shortened engine life.

14

Page 13 Page 15
Page 14
Image 14
Poulan 421469 owner manual Engine, Cleaning
Page 13 Page 15

421469 specifications

The Poulan 421469 is a notable chainsaw model widely recognized for its robustness and efficiency, making it a preferred choice among both professional landscapers and casual users alike. This chainsaw is designed to handle a variety of cutting tasks, from felling small trees to pruning branches, thanks to its reliable performance and user-friendly features.

One of the main features of the Poulan 421469 is its powerful engine. The chainsaw is equipped with a 42cc two-stroke engine, providing ample power to tackle tough cutting jobs. This engine design ensures a balance between power and fuel efficiency, allowing users to extend their cutting time without frequent stops for refueling.

The chainsaw is also notable for its 18-inch bar and chain, which not only enhances its cutting capacity but also enables smooth and efficient cuts through various types of wood. The length of the bar allows for increased reach, making it easier to handle larger branches and logs. The high-quality chain ensures durability and sharpness, providing clean cuts without excessive effort.

In addition to its power, the Poulan 421469 incorporates several technologies aimed at improving the user experience. The chainsaw features an automatic oiling system, ensuring that the bar and chain are adequately lubricated during operation. This feature reduces maintenance time for users and enhances the lifespan of the components.

Furthermore, the chainsaw is designed with an ergonomic handle, which offers comfort and control during prolonged use. The lightweight construction of the unit reduces fatigue, enabling users to work for extended periods without discomfort. A safety switch and chain brake enhance user protection, making the chainsaw a safer choice for both beginners and experienced operators.

The Poulan 421469 also emphasizes ease of use, with a tool-free assembly system that simplifies the process of changing the chain or bar. This feature is particularly appealing to users who may not be familiar with more complex chainsaw mechanisms.

In summary, the Poulan 421469 embodies a perfect blend of power, efficiency, and user-friendly features. With its strong engine, robust cutting capability, and thoughtful design elements, it stands out as a reliable and versatile tool for anyone in need of a dependable chainsaw. Whether for professional use or occasional yard work, the Poulan 421469 is equipped to meet diverse cutting needs with confidence.
Top Page Image Contents