Install Traction Drive Control ROD See Figs | Poulan 421471 instruction

ASSEMBLY / PRE-OPERATION

INSTALL TRACTION DRIVE CONTROL ROD (See Figs. 3 and 4)

The traction drive control rod has the long loop on the end of the spring as shown.

1.Slide rubber sleeve up rod and hook end of spring into pivot bracket with loop opening down as shown.

2.With top end of rod positioned under left side of control panel, push rod down and insert top end of rod into hole in drive control bracket. Secure with retainer spring.

TRACTION DRIVE

CONTROL ROD

RUBBER

SLEEVE

LOOP OPEN-

ING DOWN

PIVOT

BRACKET

FIG. 3

TRACTION DRIVE	RETAINER
CONTROL LEVER	SPRING
	TRACTION
	DRIVE
	CONTROL
	ROD
DRIVE
CONTROL
BRACKET

FIG. 4

INSTALL AUGER CONTROL ROD (See Figs. 5 and 6)

The auger control rod has the short loop on the end of the spring as shown.

1.Slide rubber sleeve up rod and hook end of spring into control arm with loop opening up as shown.

2.With top end of rod positioned under right side of control panel, push down on rod and insert end of rod into hole in auger control bracket. Secure with retainer spring.

AUGER

CONTROL

ROD

RUBBER

SLEEVE

CONTROL

ARM

LOOP

OPENING

UP

FIG. 5

	AUGER CONTROL ROD	AUGER
	RETAINER	CONTROL
	RETAINER	LEVER
	SPRING	LEVER
	SPRING
		AUGER
	CONTROL
	BRACKET

FIG. 6

6

Image 6

Poulan 421471, PP1053ES owner manual Install Traction Drive Control ROD See Figs, Install Auger Control ROD See Figs

Contents

Model Number Snow Thrower Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents EXT RA Shear Bolts and Nuts Chute Deflector Remote ControlParts Packed Separately in Carton Rotator Head Mounting Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper Handle Install Traction Drive Control ROD See Figs Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Primer OperationKnow Your Snow Thrower Ignition KEY Meets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting engine HOW to USE Your Snow Thrower Stopping To Throw Snow See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Move Forward and Backward See Fig Check Engine OIL Level See Fig To Adjust Skid Plates See FigBefore Starting the Engine ADD Gasoline See Fig Before Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has Frozen Before Each USE MaintenanceGeneral Recommendations Lubrication Cleaning Snow ThrowerEngine Chute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See Fig To Replace Belts See Fig Storage Other Troubleshooting Exploded KEY Part Description Auger Bearing Auger HousingScrapper BAR Bearing Plug Auger Assembly 30 LH Auger Assembly 30 RH Deflector Weldment Deflector Control AssemblyChute Weldment Deflector Seal Rotator Pivot Bracket LEVER/CABLE Rotator AssemblyRotator Head Pulley Pivot Repair Parts Snow Thrower Model PP1053ES Handles Handle Knob SpacerKnob RED Washer 3/8 Shifter ROD TOP Impeller ROD AssemblyTraction ROD Assembly Shifter ROD Bottom Part KEY Description Repair Parts Snow Thrower Model PP1053ES 96192001803DRIVE END Plate Speed Selector AssemblyDrive Plate Assembly Bottom PAN Repair Parts Snow Thrower Model PP1053ES Drive Axle ShaftSprocket KEY Part Description Tecumseh Engine Model LH358SA-159628A417014X428 Engine Mount Plate Belt Cover Traction BeltImpeller Belt Repair Parts Snow Thrower Model PP1053ES Wheels Cable Bracket LH Cable Bracket RH Repair Parts Snow Thrower Model PP1053ES BAG of Parts Safety Ignition KEY35062 Repair Parts Snow Thrower Model PP1053ES Decals 181037DECAL, Danger Service Notes Limited Warranty