Axle Shaft, Sprocket | Poulan 96194000900, 428558 instruction

REPAIR PARTS SNOW THROWER - MODEL 961940009 (96194000900) DRIVE

5	3
5
	4
6	01.03.002-A

	7
1b	4
8	3
	3
	1a

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION
1	404923	AXLE ASSEMBLY (assy of 1a,1b)
1a	404307	AXLE SHAFT
1b	9465M1	ROLL PIN 3/16 X 1.50
2	402691	SPROCKET
3	174697	THRUST WASHER
4	179830	BEARING

5146315 SCREW 5/16−18 X .625

617490508 SCREW 5/16−18 X .500

7	155443	KLIK PIN 1/4 X 1.50
8	189282	SQUARE KEY

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Page 31

Image 31

Poulan 96194000900, 428558 owner manual Axle Shaft, Sprocket

Contents

Snow Thrower Model Number Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Unfold Upper Handle Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from Carton Install Auger Control ROD See Figs Install Traction Drive Control ROD See Figs Install Chute Deflector Remote Control See Figs Install Discharge Chute / Chute Rotater Head See FigCheck Tire Pressure Ignition KEY OperationKnow Your Snow Thrower Primer Recoil auxiliary starter handle used for starting engine Meets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow Thrower Power Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig Check Engine OIL Level See Fig To Adjust Skid Plates See FigBefore Starting the Engine Scraper BAR See Fig If Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before Stopping Lubrication MaintenanceGeneral Recommendations Before Each USE Snow Thrower CleaningEngine Shear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute Deflector To Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig Carburetor Engine OIL StorageOther Fuel System Troubleshooting KEY Part Description Auger HousingAuger Assembly 30 LH Auger Assembly 30 RH 23 22 Impeller Pulley Gearbox Assembly178675X008 Corner Bracket Clean OUT Tool Bearing Bearing Plug Auger Bearing Shield Retainer Strap Knob BlackPOP Rivet Chute Snow Shield Rotator Pivot Bracket LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator Head Interlock CAM Loop Handle LHLoop Handle RH Interlock Spring Washer 3/8 SpacerKnob RED Handle Knob Shifter ROD Bottom Impeller RODTraction ROD Shifter ROD TOP Console Panel Wire HarnessLower Tube Pivot Support Sprocket Axle Shaft Exploded Rubber Ring AssemblyDrive Plate Assembly Speed Selector 427963X428 Cover AssemblyComplete LCT Engine Frame Idler Pulley Impeller BeltTraction Belt Idler ARM Bracket Clutch Slide CoverWheel Driver Retainer Ring Wheel Lobe Cable Bracket RH Cable Bracket LH 422663 Safety Ignition KEY DECAL, Instruction 181037DECAL, Danger DECAL, DANGER, Deflector HOP Limited Warranty

REPAIR PARTS SNOW THROWER - MODEL 961940009 (96194000900) DRIVE

KEY

AXLE SHAFT

SPROCKET

THRUST WASHER

BEARING

SQUARE KEY