422663, Safety Ignition KEY | Poulan 428558, 96194000900 specs

REPAIR PARTS SNOW THROWER - MODEL 961940009 (96194000900) BAG OF PARTS

01.14.003-B

4	KEY	PART
			DESCRIPTION
6	NO.	NO.
5	1	198563	POWER CORD
8
	2	169675	RETAINER PIN
7

3180684X008 WRENCH

4184505 REMOTE SPRING

		5	179829	SHOULDER BOLT 1/4-20
	9 10	6	191730	LOCKNUT 1/4-20
	9 10	7	72250505	CARRIAGE BOLT 5/16-18 X 5/8
		8	751153	LOCKNUT 5/16-18
		9	73800600	LOCKNUT 3/8-16
		10	19131316	WASHER 3/8
		11	192090	SHEAR BOLT 1/4-20 X 1-13/16
		12	73800400	LOCKNUT 1/4-20
1	12
1
	11

	KEY	PART	DESCRIPTION
	NO.	NO.	DESCRIPTION
1	1	422663	SAFETY IGNITION KEY
1

01.14.009-A

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Page 38

Image 38

Poulan 428558, 96194000900 owner manual 422663, Safety Ignition KEY

Contents

Model Number Snow Thrower Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper Handle Install Traction Drive Control ROD See Figs Install Auger Control ROD See Figs Check Tire Pressure Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Primer OperationKnow Your Snow Thrower Ignition KEY Meets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting engine HOW to USE Your Snow Thrower Stopping To Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig Scraper BAR See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See Fig Before Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has Frozen Before Each USE MaintenanceGeneral Recommendations Lubrication Engine CleaningSnow Thrower Chute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See Fig To Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine Speed Fuel System StorageOther Engine OIL Troubleshooting Auger Assembly 30 RH Auger HousingAuger Assembly 30 LH KEY Part Description 23 22 Bearing Gearbox Assembly178675X008 Corner Bracket Clean OUT Tool Impeller Pulley Auger Bearing Bearing Plug Chute Snow Shield Knob BlackPOP Rivet Shield Retainer Strap Rotator Head LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator Pivot Bracket Interlock Spring Loop Handle LHLoop Handle RH Interlock CAM Handle Knob SpacerKnob RED Washer 3/8 Shifter ROD TOP Impeller RODTraction ROD Shifter ROD Bottom Pivot Support Wire HarnessLower Tube Console Panel Axle Shaft Sprocket Exploded Speed Selector AssemblyDrive Plate Assembly Rubber Ring Frame Cover AssemblyComplete LCT Engine 427963X428 Idler ARM Bracket Impeller BeltTraction Belt Idler Pulley Wheel Lobe CoverWheel Driver Retainer Ring Clutch Slide Cable Bracket LH Cable Bracket RH Safety Ignition KEY 422663 DECAL, DANGER, Deflector 181037DECAL, Danger DECAL, Instruction Limited Warranty HOP

KEY

SHOULDER BOLT 1/4-20

WASHER 3/8

KEY

422663

SAFETY IGNITION KEY

01.14.009-A