Impeller Belt, Traction Belt, Idler Pulley | Poulan 96194000900

REPAIR PARTS SNOW THROWER - MODEL 961940009 (96194000900) CHASSIS / ENGINE / PULLEYS

27

23

22

			13
			21
			20
25
24
13	21		19
15			26
15					18
					18
11					17
					17
12					16
13		14			16
13		14
			7
		5
9
				4	6
				4
10			3		1
10					2
				8

01.21.020-A

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION
1	419888	IMPELLER BELT
2	427304	TRACTION BELT
3	423723X479	IDLER ARM BRACKET
4	180523	IDLER PULLEY
5	423990X479	IDLER BRACKET
6	426589	NUT 5/16-18
7	74780524	SCREW 5/16-18 X 1.50
8	424297	SHOULDER BOLT 5/16-18 X .50
9	751153	NUT 5/16-18 LOCK
10	428867	SCREW 5/16-18 X .625

11427576 TRACTION IDLER BRACKET

12180522 TRACTION PULLEY

13	59289	WASHER
14	73800500	NUT 5/16-18

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION
15	74780520	SCREW 5/16-18 X 1.25
16	851084	SCREW 3/8-24 X 1 .375
17	19132005	WASHER

18425934 PULLEY ENG IMPELLER

19425933 PULLEY ENG TRACTION

2074610516 SCREW 5/16-24 X 1.00

2110040500 LOCKWASHER 5/16

22

155452

BELT GUIDE

2311050500 LOCKWASHER 5/16

24175331 IDLER BUSHING

2519112206 WASHER

2674610520 SCREW 5/16-24 X 1.25

2774760608 SCREW 3/8-16 X .750

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

35

Image 35

Poulan 96194000900, 428558 Impeller Belt, Traction Belt, Idler ARM Bracket, Idler Pulley, Idler Bracket, Belt Guide

Contents

Snow Thrower Model Number Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Unfold Upper Handle Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from Carton Install Auger Control ROD See Figs Install Traction Drive Control ROD See Figs Check Tire Pressure Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Ignition KEY OperationKnow Your Snow Thrower Primer Recoil auxiliary starter handle used for starting engine Meets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow Thrower To Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig Check Engine OIL Level See Fig To Adjust Skid Plates See FigBefore Starting the Engine Scraper BAR See Fig If Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before Stopping Lubrication MaintenanceGeneral Recommendations Before Each USE Engine CleaningSnow Thrower Shear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute Deflector To Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig Carburetor Engine OIL StorageOther Fuel System Troubleshooting KEY Part Description Auger HousingAuger Assembly 30 LH Auger Assembly 30 RH 23 22 Impeller Pulley Gearbox Assembly178675X008 Corner Bracket Clean OUT Tool Bearing Bearing Plug Auger Bearing Shield Retainer Strap Knob BlackPOP Rivet Chute Snow Shield Rotator Pivot Bracket LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator Head Interlock CAM Loop Handle LHLoop Handle RH Interlock Spring Washer 3/8 SpacerKnob RED Handle Knob Shifter ROD Bottom Impeller RODTraction ROD Shifter ROD TOP Console Panel Wire HarnessLower Tube Pivot Support Sprocket Axle Shaft Exploded Rubber Ring AssemblyDrive Plate Assembly Speed Selector 427963X428 Cover AssemblyComplete LCT Engine Frame Idler Pulley Impeller BeltTraction Belt Idler ARM Bracket Clutch Slide CoverWheel Driver Retainer Ring Wheel Lobe Cable Bracket RH Cable Bracket LH 422663 Safety Ignition KEY DECAL, Instruction 181037DECAL, Danger DECAL, DANGER, Deflector HOP Limited Warranty