SERVICE AND ADJUSTMENTS

TO REPLACE BELTS (See Fig. 20)

The auger and traction drive belts are not adjustable. If the belts are damaged or begin to slip from wear, they should be replaced. It is recommended that the belt(s) be replaced by a service center/department.

NOTE: It is recommended that both the auger and traction drive belt be replaced at the same time.

The V-belts on your snow thrower are of special construc- tion and should be replaced by original equipment manu- facturer (OEM) belts available from your nearest service center/department. Using other than OEM belts can cause personal injury or damage to the snow thrower.

WARNING: Belt replacement requires separation of the snow thrower. While separating the auger housing from the frame assembly, it is important that an assistant stand in the operating position and hold the snow thrower handles. Serious personal injury and/ or damage to the unit could occur if the snow thrower should fall during the belt changing process.

FRAME

AUGER

ASSEMBLY

HOUSING

HANDLES

1.REMOVE GASOLINE FROM FUEL TANK - Drain gasoline from fuel tank into a suitable container, out- doors, away from fire or flame. Wipe up any spilled gasoline.

2.REMOVE DISCHARGE CHUTE - Loosen locknut securing chute rotator head to mounting bracket only enough to allow chute rotator head to be raised and discharge chute to be removed from snow thrower.

3.REMOVE BELT COVER - See “TO REMOVE BELT COVER” in this section of this manual.

4.REMOVE ENGINE PULLEY - Remove bolt, flat washer securing pulley to engine crankshaft. Remove outside (auger) pulley only from crankshaft.

5.SEPARATE SNOW THROWER - With your assistant standing in the operating position holding the handles, remove the two (2) bolts holding the auger housing and frame together.

WARNING: As the last bolt is removed, have your assistant carefully lower the handles down to the ground.

6.REMOVE HAIRPIN FROM CLUTCH ROD and re- move clutch rod from swing plate. Tip swing plate forward.

7.REMOVE AUGER BELT from around pulley.

8.RELIEVE TENSION ON TRACTION DRIVE BELT IDLER and remove traction drive belt from around pulleys.

HINT: Insert a 3/8" drive ratchet (in the “ON” position) into the square hole in idler arm and rotate ratchet clockwise to relieve tension.

9.With tension relieved on idler, install new traction drive belt around pulleys and inside belt keepers.

10.Install clutch rod in swing plate; secure with hairpin.

11.Place auger belt around and inside the groove of auger pulley only.

12.While your assistant slowly raises handles to rejoin the auger housing and frame assembly, pull up on the auger belt and squeeze sides together above pulley so belt is fully seated in groove of pulley.

13.Move idler arm so it does not hit impeller pulley as you bring snow thrower completely together and check carefully for proper routing of belts. If auger belt has become dislodged from the pulley (by catching the idler arm bracket while bringing snow thrower together), separate the snow thrower and repeat step 12. Belt must be fully seated in pulley groove when bringing the snow thrower together.

14.Install the two (2) hex bolts and tighten securely.

15.INSTALL ENGINE PULLEY - Place belt in pulley groove and slide pulley on crankshaft. Install flat washer, bolt and tighten securely (41-47 N-m torque). Make sure belt is inside belt keeper.

16.INSTALL BELT COVER and two (2) screws. Tighten securely.

17.INSTALL DISCHARGE CHUTE – See “INSTALL DIS- CHARGE CHUTE / CHUTE ROTATER HEAD” in the Assembly / Pre-Operation section of this manual.

 

BELT KEEPER

 

 

 

TRACTION DRIVE BELT

 

 

ENGINE

FLAT WASHER

 

PULLEY

 

 

 

 

 

BOLT

 

IDLER ARM

 

AUGER

SQUARE

 

BELT

HOLE

 

 

 

CLUTCHING

 

 

 

IDLER ARM

 

 

 

BRACKET

 

 

FRAME

AUGER PULLEY

AUGER

HOUSING

 

 

 

BOLTS

 

16

FIG. 20

Page 16
Image 16
Poulan 428701, 96198002601 owner manual To Replace Belts See Fig

96198002601, 428701 specifications

The Poulan 428701,96198002601 is a powerful and efficient chainsaw designed for homeowners and professionals alike. This model combines advanced technology with user-friendly features, making it a top choice for those looking to tackle various chopping and cutting tasks with ease.

One of the key features of this chainsaw is its robust engine, which provides dependable performance. The Poulan 428701 is equipped with a 40cc two-cycle engine that delivers ample power for cutting through large tree limbs, firewood preparation, and even light commercial work. The engine's design focuses on fuel efficiency, ensuring that users can work longer without frequent refueling.

In terms of technology, the chainsaw incorporates a tool-less chain tensioning system that allows users to adjust the chain’s tension quickly and easily. This feature not only saves time but also enhances safety, as a correctly tensioned chain reduces the risk of kickback and improves cutting performance. The easy-access air filter ensures that maintenance is simple, allowing users to keep their chainsaw performing optimally with minimal effort.

The Poulan 428701 also boasts a lightweight design, weighing in at just under 12 pounds. This makes it manageable for extended use without causing fatigue, making it suitable for both beginners and experienced users. The ergonomic handle is designed for comfort, providing a secure grip that enhances control during operation.

Safety is a significant concern with power tools, and this chainsaw is equipped with a chain brake mechanism. The chain brake stops the chain immediately in case of a kickback, protecting the user from potentially serious injuries. Its low vibration technology further reduces operator fatigue and increases comfort for prolonged use.

Another notable characteristic of the Poulan 428701 is its durable construction. Built with high-quality materials, this chainsaw is designed to withstand the rigors of regular use while maintaining its performance. The bar and chain are designed for longevity, with easy compatibility for replacements when necessary.

In summary, the Poulan 428701,96198002601 chainsaw is a reliable and efficient tool that combines power, safety, and ease of use. With features such as a powerful engine, tool-less chain tensioning, low vibration, and a focus on user comfort, it caters to a wide range of cutting needs, making it a worthwhile addition to any toolkit. Whether for home landscaping or professional use, this chainsaw delivers performance that users can trust.