Auger Housing, Scraper BAR, Auger Bearing | Poulan 429264 guide

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP1150E27 (96198003301)

AUGER HOUSING / IMPELLER ASSEMBLY

1

		KEY	PART	DESCRIPTION
	3 (5x)	NO.	NO.	DESCRIPTION
	3 (5x)	1	404929X428	AUGER HOUSING 27
	4 (5x)	1	404929X428	AUGER HOUSING 27
	4 (5x)	2	404932X428	SCRAPER BAR
2		2	404932X428	SCRAPER BAR
2		3	72270505	CARRIAGE BOLT 5/16−18 X .625
		4	155377	NUT 5/16−18
	01.07.002-A

2	3

1

1

2

		KEY	PART	DESCRIPTION
		NO.	NO.	DESCRIPTION
		1	420478	AUGER BEARING
3		2	411939	BEARING PLUG
	01.07.024-B	3	179582	SCREW 5/16−18 X 1.00
	01.07.024-B

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

24

Image 24

Poulan 429264, 96198003301 owner manual Auger Housing, Scraper BAR, Auger Bearing, Bearing Plug

Contents

Model Number Snow Thrower Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from Carton Install Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See Fig Install Chute Deflector Remote Control See Figs Check Tire Pressure Operation Know Your Snow ThrowerPrimer Ignition KEY Meets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engine HOW to USE Your Snow Thrower StoppingTo USE Choke Control See Fig To Control Snow Discharge See Fig Using the CLEAN-OUT Tool See Fig Power Steering Operation See FigTo Throw Snow See Fig To Move Forward and Backward See Fig To Adjust Skid Plates See Fig Before Starting the EngineScraper BAR See Fig Check Engine OIL Level See Fig Snow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has Frozen Maintenance General RecommendationsBefore Each USE Lubrication Cleaning Engine Service and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See Fig To Replace Belts See Fig To Adjust Cable Tension See Fig To Remove Wheels See FigCarburetor Engine Speed Storage OtherFuel System Engine OIL Troubleshooting Service Notes 23 22 KEY Part Description Auger Housing Scraper BARAuger Bearing Bearing Plug Auger 27 LH Auger 27 RH Knob Black POP RivetShoulder Screw Deflector Spring LEVER/CABLE Rotator Assembly Cable Assembly AdjustableCable Assembly Heat Shield Rotator Head Loop Handle LH Loop Handle RHLower Tube Pivot Support Spacer RetainerKnob RED Handle Knob Carriage Bolt 5/16-18 X 155377 NUT 5/16-18 169675 Wire Harness Console PanelHeadlight Bezel Flood Headlight Repair Parts Snow Thrower - Model Number PP1150E27 Drive Speed Selector Assembly Drive Plate AssemblyWheel HUB END Plate 01.03.002-A ENGINE, B&S Frame423185X428 Engine Mounting Plate Impeller Belt Traction BeltIdler ARM Bracket Idler Pulley Cover Assembly Repair Parts Snow Thrower - Model Number PP1150E27 Wheels Cable Bracket LH Cable Bracket RH Cover Wheel Driver Retainer RingWheel Lobe Clutch Slide Safety Ignition KEY 193071 181037 DECAL, DangerDECAL, DANGER, Deflector DECAL, Instruction Service Notes Service Notes Limited Warranty