01.03.002-A | Poulan 429264, 96198003301 guide

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP1150E27 (96198003301)

DRIVE

6

	7
1b	4
8	3
	3
1b
7	1a
	1a

			KEY	PART	DESCRIPTION
		2	NO.	NO.	DESCRIPTION
		2	1	404923	AXLE ASSEMBLY (assy of 1a,1b)
			1	404923	AXLE ASSEMBLY (assy of 1a,1b)
5	3		1a	404307	AXLE SHAFT
5			1b	184206	ROLL PIN 3/16 X 1.50
	4		1b	184206	ROLL PIN 3/16 X 1.50
	4		2	402691	SPROCKET
6	01.03.002-A		3	174697	THRUST WASHER
			4	179830	BEARING
			5	146315	SCREW 5/16−18 X .625
			6	17490508	SCREW 5/16−18 X .500
			7	155443	KLIK PIN 1/4 X 1.50
			8	189282	SQUARE KEY

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

34

Image 34

Poulan 429264, 96198003301 owner manual 01.03.002-A

Contents

Model Number Snow Thrower Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from Carton Install Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See Fig Install Chute Deflector Remote Control See Figs Check Tire Pressure Primer OperationKnow Your Snow Thrower Ignition KEY Meets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engine To USE Choke Control See Fig HOW to USE Your Snow ThrowerStopping To Control Snow Discharge See Fig To Throw Snow See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Move Forward and Backward See Fig Scraper BAR See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See Fig Before Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has Frozen Before Each USE MaintenanceGeneral Recommendations Lubrication Cleaning Engine Chute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See Fig To Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine Speed Fuel System StorageOther Engine OIL Troubleshooting Service Notes 23 22 KEY Part Description Auger Bearing Auger HousingScraper BAR Bearing Plug Auger 27 LH Auger 27 RH Shoulder Screw Knob BlackPOP Rivet Deflector Spring Cable Assembly Heat Shield LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator Head Lower Tube Loop Handle LHLoop Handle RH Pivot Support Knob RED SpacerRetainer Handle Knob Carriage Bolt 5/16-18 X 155377 NUT 5/16-18 169675 Headlight Bezel Wire HarnessConsole Panel Flood Headlight Repair Parts Snow Thrower - Model Number PP1150E27 Drive Wheel HUB Speed Selector AssemblyDrive Plate Assembly END Plate 01.03.002-A 423185X428 ENGINE, B&SFrame Engine Mounting Plate Idler ARM Bracket Impeller BeltTraction Belt Idler Pulley Cover Assembly Repair Parts Snow Thrower - Model Number PP1150E27 Wheels Cable Bracket LH Cable Bracket RH Wheel Lobe CoverWheel Driver Retainer Ring Clutch Slide Safety Ignition KEY 193071 DECAL, DANGER, Deflector 181037DECAL, Danger DECAL, Instruction Service Notes Service Notes Limited Warranty