Check Tire Pressure

ASSEMBLY / PRE-OPERATION

INSTALL CHUTE DEFLECTOR REMOTE CONTROL (See Figs. 8A and 8B)

1.Install remote cable bracket to discharge chute with 5/16-18 carriage bolt and 5/16-18 locknut as shown. Tighten securely.

2.Install remote cable eyelet to chute deflector with 1/4-20 shoulder bolt and 1/4-20 locknut as shown. Tighten nut securely. Cable eyelet will be loose on shoulder bolt.

3.Install spring hooks between hex nuts on chute rotater head and into hole in chute deflector as shown.

	1/4-20	SPRING
	1/4-20	CHUTE
	SHOULDER	CHUTE
	SHOULDER	DEFLECTOR
	BOLT	DEFLECTOR
	BOLT
		HOOK
		BETWEEN
		HEX NUTS
		ON CHUTE
	1/4-20	ROTATER
	LOCKNUT	HEAD
		5/16-18
		CARRIAGE
		BOLT
	CABLE
	EYELET
	REMOTE
	CABLE
	BRACKET
	5/16-18
	LOCKNUT

Fig. 8A

CHUTE DEFLECTOR

CONTROL LEVER

Fig. 8B

The tires on your snow thrower were overinflated at the fac- tory for shipping purposes. Correct and equal tire pressure is important for best snow throwing performance.

•Reduce tire pressure to 14-17 PSI.

Page 7

Image 7

Poulan 435551 owner manual Install Chute Deflector Remote Control See Figs a and 8B, Check Tire Pressure

Contents

Snow Thrower Model Number Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in Carton Install Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See Figs Check Tire Pressure Install Chute Deflector Remote Control See Figs a and 8B Ignition KEY OperationKnow Your Snow Thrower Primer Recoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety Requirements To USE Choke Control See Fig HOW to USE Your Snow ThrowerStopping To USE Fuel SHUT-OFF Valve See Fig To Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Throw Snow See Fig Check Engine OIL Level See Fig To Adjust Skid Plates See FigBefore Starting the Engine Scraper BAR See Fig If Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before Stopping Lubrication MaintenanceGeneral Recommendations Before Each USE Engine Cleaning Shear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute Deflector To Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig Carburetor Engine OIL StorageOther Fuel System Troubleshooting KEY Part Description Auger HousingAuger Assembly LH Auger Assembly RH Exploded Impeller Pulley Gearbox Assembly178675X431 Corner Bracket Clean OUT Tool Bearing Skid Plate RH Auger BearingBearing Plug Skid Plate LH POP Rivet Knob BlackChute Snow Shield 419822X431 Shield Retainer Strap Rotator Pivot Bracket LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator Head Lower Handle 196944X431 Panel Bracket LH 196943X431 Panel Bracket RHHandle Grip Washer Handle Knob SpacerRetainer Knob RED Shifter ROD Bottom Impeller RODTraction ROD Shifter ROD TOP Flood Headlight Wire HarnessConsole Panel Headlight Bezel Sprocket Axle Shaft Exploded END Plate Speed Selector AssemblyDrive Plate Assembly Wheel HUB Engine Mounting Plate Complete LCT EngineFrame 427963X428 Idler Pulley Impeller BeltTraction Belt Idler ARM Bracket Cable Bracket RH 432333X421 Wheel Assembly LH 432334X421 Wheel Assembly RH01.06.017-A Cable Bracket LH Clutch Slide CoverWheel Driver Retainer Ring Wheel Lobe 422663 Safety Ignition KEY DECAL, Speed Control DECAL, DangerDECAL, DANGER, Deflector DECAL, Instruction Limited Warranty

Poulan 435551 Install Chute Deflector Remote Control See Figs a and 8B, Check Tire Pressure

Models: 435551

ASSEMBLY / PRE-OPERATION

INSTALL CHUTE DEFLECTOR REMOTE CONTROL (See Figs. 8A and 8B)

CHECK TIRE PRESSURE