To Remove Wheels See Fig, Carburetor, Engine Speed | Poulan 435551

SERVICE AND ADJUSTMENTS

TO REMOVE WHEELS (See Fig. 22)

•Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the axle hole closest to the end of the shaft – do not use the hole in the wheel hub (if equipped). Inner hole in axle and hole in wheel hub are not used for your model snow thrower.

NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

KLIK PIN (INSTALL	OUTER HOLE
IN OUTER HOLE
OF AXLE ONLY)

AXLE

WHEEL

WHEEL HUB

Fig. 22

NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

ENGINE

See engine manual.

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000 feet (2,134 meters). If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a qualified service center.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a qualified service center, which has proper equipment and experience to make any necessary adjustments.

TO ADJUST CABLE TENSION (See Fig. 23)

Adjust cable tension by turning the adjuster turn buckle, located on the right hand cable. Grasp the long section tightly and turn the short section to lengthen the adjuster. Adjust until cable is snug.

ADJUSTER TURN

BUCKLE

Fig. 23

18

Image 18

Poulan 435551 owner manual To Remove Wheels See Fig, Carburetor, Engine Speed, To Adjust Cable Tension See Fig

Contents

Model Number Snow Thrower Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from Carton Install Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotator Head See Fig Install Chute Deflector Remote Control See Figs a and 8B Check Tire Pressure Primer OperationKnow Your Snow Thrower Ignition KEY Meets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engine To USE Fuel SHUT-OFF Valve See Fig HOW to USE Your Snow ThrowerStopping To USE Choke Control See Fig To Throw Snow See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Move Forward and Backward See Fig Scraper BAR See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See Fig Before Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has Frozen Before Each USE MaintenanceGeneral Recommendations Lubrication Cleaning Engine Chute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See Fig To Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine Speed Fuel System StorageOther Engine OIL Troubleshooting Auger Assembly RH Auger HousingAuger Assembly LH KEY Part Description Exploded Bearing Gearbox Assembly178675X431 Corner Bracket Clean OUT Tool Impeller Pulley Skid Plate LH Auger BearingBearing Plug Skid Plate RH Knob Black POP RivetChute Snow Shield 419822X431 Shield Retainer Strap Rotator Head LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator Pivot Bracket Washer 196944X431 Panel Bracket LH 196943X431 Panel Bracket RHHandle Grip Lower Handle Knob RED SpacerRetainer Handle Knob Shifter ROD TOP Impeller RODTraction ROD Shifter ROD Bottom Headlight Bezel Wire HarnessConsole Panel Flood Headlight Axle Shaft Sprocket Exploded Wheel HUB Speed Selector AssemblyDrive Plate Assembly END Plate 427963X428 Complete LCT EngineFrame Engine Mounting Plate Idler ARM Bracket Impeller BeltTraction Belt Idler Pulley Cable Bracket LH 432333X421 Wheel Assembly LH 432334X421 Wheel Assembly RH01.06.017-A Cable Bracket RH Wheel Lobe CoverWheel Driver Retainer Ring Clutch Slide Safety Ignition KEY 422663 DECAL, Instruction DECAL, DangerDECAL, DANGER, Deflector DECAL, Speed Control Limited Warranty