Handle Grip, Washer, Lower Handle | Poulan 435551 specification

REPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS24 (96198002701)

HANDLES

			5
				1
			6
		8		7
		2
5	8		3	9
	8
	6		7
			7
	8
	4	9

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION

1419800X431 PLOW HANDLE LH

2419801X431 PLOW HANDLE RH

3196944X431 PANEL BRACKET LH

4196943X431 PANEL BRACKET RH

199513

HANDLE GRIP

674780512 SCREW 5/16−18 X .750

774780524 SCREW 5/16−18 X 1.50

8	751153	NUT 5/16−18
9	155415	WASHER

01.08.003-A

	KEY	PART	DESCRIPTION
	NO.	NO.	DESCRIPTION
	1	419797X431	LOWER HANDLE
	2	427513X431	PIVOT SUPPORT WELDMENT
	3	428867	SCREW 5/16−18 X .750
2	4	17000616	SCREW 3/8−16 X 1.00

01-05-013-A

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Page 27

Image 27

Poulan 435551 owner manual 196944X431 Panel Bracket LH 196943X431 Panel Bracket RH, Handle Grip, Washer, Lower Handle

Contents

Snow Thrower Model Number Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in Carton Install Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See Figs Check Tire Pressure Install Chute Deflector Remote Control See Figs a and 8B Ignition KEY OperationKnow Your Snow Thrower Primer Recoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety Requirements To USE Choke Control See Fig HOW to USE Your Snow ThrowerStopping To USE Fuel SHUT-OFF Valve See Fig To Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Throw Snow See Fig Check Engine OIL Level See Fig To Adjust Skid Plates See FigBefore Starting the Engine Scraper BAR See Fig If Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before Stopping Lubrication MaintenanceGeneral Recommendations Before Each USE Engine Cleaning Shear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute Deflector To Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig Carburetor Engine OIL StorageOther Fuel System Troubleshooting KEY Part Description Auger HousingAuger Assembly LH Auger Assembly RH Exploded Impeller Pulley Gearbox Assembly178675X431 Corner Bracket Clean OUT Tool Bearing Skid Plate RH Auger BearingBearing Plug Skid Plate LH Knob Black POP RivetChute Snow Shield 419822X431 Shield Retainer Strap Rotator Pivot Bracket LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator Head Lower Handle 196944X431 Panel Bracket LH 196943X431 Panel Bracket RHHandle Grip Washer Handle Knob SpacerRetainer Knob RED Shifter ROD Bottom Impeller RODTraction ROD Shifter ROD TOP Flood Headlight Wire HarnessConsole Panel Headlight Bezel Sprocket Axle Shaft Exploded END Plate Speed Selector AssemblyDrive Plate Assembly Wheel HUB Engine Mounting Plate Complete LCT EngineFrame 427963X428 Idler Pulley Impeller BeltTraction Belt Idler ARM Bracket Cable Bracket RH 432333X421 Wheel Assembly LH 432334X421 Wheel Assembly RH01.06.017-A Cable Bracket LH Clutch Slide CoverWheel Driver Retainer Ring Wheel Lobe 422663 Safety Ignition KEY DECAL, Speed Control DECAL, DangerDECAL, DANGER, Deflector DECAL, Instruction Limited Warranty

Poulan 435551 196944X431 Panel Bracket LH 196943X431 Panel Bracket RH, Handle Grip, Washer

Models: 435551

REPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS24 (96198002701)

HANDLES

KEY

3196944X431 PANEL BRACKET LH

4196943X431 PANEL BRACKET RH

HANDLE GRIP

WASHER

KEY

LOWER HANDLE

PIVOT SUPPORT WELDMENT