Loop Handle LH, Loop Handle RH, 419797X431 | Poulan 438364 specs

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR8P27ES (96192004601)

HANDLES

3

3

		KEY	PART	DESCRIPTION
4	4	NO.	NO.	DESCRIPTION
4		1	419798X431	LOOP HANDLE LH
	1	2	419799X431	LOOP HANDLE RH
3		3	74780524	SCREW 5/16−18 X 1.50
3		4	751153	NUT 5/16−18
4		4	751153	NUT 5/16−18
4
3
2

01.08.004-B

1

4

3

4

4

01-05-013-A

	KEY	PART	DESCRIPTION
	NO.	NO.	DESCRIPTION
2	1	419797X431	LOWER HANDLE

2427513X431 PIVOT SUPPORT WELDMENT

3428867 SCREW 5/16−18 X .750

417000616 SCREW 3/8−16 X 1.00

3

4

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 28

Image 28

Poulan 438364, 96192004601 Loop Handle LH, Loop Handle RH, 419797X431, Lower Handle, 427513X431 Pivot Support Weldment

Contents

Model Number Snow Thrower Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from Carton Install Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See Fig Install Chute Deflector Remote Control See Figs Check Tire Pressure Operation Know Your Snow ThrowerPrimer Ignition KEY Meets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engine HOW to USE Your Snow Thrower StoppingTo USE Choke Control See Fig To Control Snow Discharge See Fig Using the CLEAN-OUT Tool See Fig Power Steering Operation See FigTo Throw Snow See Fig To Move Forward and Backward See Fig To Adjust Skid Plates See Fig Before Starting the EngineScraper BAR See Fig Check Engine OIL Level See Fig Snow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has Frozen Maintenance General RecommendationsBefore Each USE Lubrication Cleaning Engine Service and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See Fig To Replace Belts See Fig To Adjust Cable Tension See Fig To Remove Wheels See FigCarburetor Engine Speed Storage OtherFuel System Engine OIL Troubleshooting Service Notes Exploded KEY Part Description Auger Housing Scraper BARAuger Bearing Bearing Plug Auger 27 LH Auger 27 RHSkid Plate LH Skid Plate RH Deflector Seal Knob BlackPOP Rivet Chute Snow Shield 419822X431 Shield Retainer Strap KEY Part Loop Handle LH Loop Handle RH419797X431 Lower Handle Spacer RetainerKnob RED Handle Knob Carriage Bolt 5/16-18 X 155377 NUT 5/16-18 169675 Wire Harness Console PanelHeadlight Bezel Flood Headlight Repair Parts Snow Thrower - Model Number PR8P27ES Drive Speed Selector Assembly Drive Plate AssemblyWheel HUB END Plate Axle Shaft Sprocket ENGINE, B&S Frame436146X421 Engine Mount Plate 428684 Cover Wheel DriverWheel Lobe Clutch Slide Wheel Assembly LH 432337X428432338X428 Cable Bracket LH Safety Ignition KEY 193071 435840 Shifter ROD TOP Shifter ROD BottomKIT Harness Conn B&S DECAL, Danger 181037DECAL, DANGER, Deflector Service Notes Service Notes Limited Warranty