Console Panel, Headlight Bezel, Wire Harness | Poulan 96192004602

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR8P27ES (96192004602)

HANDLES

7	4

	3			5
	2			KEY	PART	DESCRIPTION
				NO.	NO.	DESCRIPTION
				1	182906	CONSOLE PANEL
				2	178668	HEADLIGHT BEZEL
	5	4	1	3	180927	FLOOD HEADLIGHT
6		4		4	184471	SHOULDERSCREW10−24X.625
				4	184471	SHOULDERSCREW10−24X.625
				5	175262	SCREW 10−24 X 1.25
				6	178770	WIRE HARNESS
				7	183784	BULB
		01.10.007-B

4

3

	5	2	KEY	PART
		2	NO.	NO.	DESCRIPTION
			NO.	NO.	DESCRIPTION
			1	412675X431	INTERLOCK SPRING
			2	414572	INTERLOCK CAM
		1	3	178831	TORSION SPRING
			4	169675	RETAINER
			5	17060410	SCREW 1/4−20 X .625
			6	421252X431	INTERLOCK STOP
		6	01.08.007-B

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 31

Image 31

Poulan 96192004602, 438371 Console Panel, Headlight Bezel, Flood Headlight, SHOULDERSCREW10−24X.625, Wire Harness, Bulb

Contents

Snow Thrower Model Number Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in Carton Install Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See Figs Check Tire Pressure Install Chute Deflector Remote Control See Figs Ignition KEY OperationKnow Your Snow Thrower Primer Recoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety Requirements To Control Snow Discharge See Fig HOW to USE Your Snow ThrowerStopping To USE Choke Control See Fig To Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Throw Snow See Fig Check Engine OIL Level See Fig To Adjust Skid Plates See FigBefore Starting the Engine Scraper BAR See Fig If Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before Stopping Lubrication MaintenanceGeneral Recommendations Before Each USE Engine Cleaning Shear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute Deflector To Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig Carburetor Engine OIL StorageOther Fuel System Troubleshooting Service Notes Exploded KEY Part Description Bearing Plug Auger HousingScraper BAR Auger Bearing Skid Plate RH Auger 27 LHAuger 27 RH Skid Plate LH Chute Snow Shield 419822X431 Shield Retainer Strap Deflector SealKnob Black POP Rivet KEY Part Lower Handle Loop Handle LHLoop Handle RH 419797X431 Handle Knob SpacerRetainer Knob RED Carriage Bolt 5/16-18 X 155377 NUT 5/16-18 169675 Flood Headlight Wire HarnessConsole Panel Headlight Bezel Repair Parts Snow Thrower - Model Number PR8P27ES Drive END Plate Speed Selector AssemblyDrive Plate Assembly Wheel HUB Sprocket Axle Shaft Engine Mounting Plate ENGINE, B&SFrame 436146X421 428684 Clutch Slide CoverWheel Driver Wheel Lobe Cable Bracket LH Wheel Assembly LHCable Bracket RH 193071 Safety Ignition KEY DECAL, Danger 181037DECAL, DANGER, Deflector Service Notes Service Notes Service Notes Limited Warranty