ON/STOP SWITCH

(SIDE VIEW)

ON

STOP

1.Move ON/STOP switch to the ON posi- tion.

2.Pull choke/fast idle lever out to the full extent (to the FULL CHOKE position).

3.Slowly press primer bulb 6 times.

4.Pull the starter rope sharply 5 times with your right hand. Then, proceed to the next step.

NOTE: If the engine sounds as if it is trying to start before the 5th pull, stop pulling and immediately proceed to the next step.

5.Push the choke/fast idle lever in to the HALF CHOKE position.

CHOKE/FAST IDLE LEVER

(SIDE VIEW)

Choke/ fast idle lever OFF HALF FULL

6.Pull the starter rope sharply with your right hand until the engine starts.

7.Allow the engine to run for approximate- ly 5 seconds. Then, squeeze and re- lease the throttle trigger to allow engine to return to idle speed.

STARTING A WARM ENGINE

1.Move ON/STOP switch to the ON posi- tion.

2.Pull the choke/fast idle lever out to the HALF CHOKE position.

3.Slowly press primer bulb 6 times.

4.Pull the starter rope sharply with your right hand until the engine starts.

5.Squeeze and release throttle trigger to allow engine to return to idle speed.

DIFFICULT STARTING (or starting a flooded engine)

The engine may be flooded with too much fuel if it has not started after 10 pulls. Flooded engines can be cleared of excess fuel by pushing the choke/fast idle lever in completely (to the OFF CHOKE position) and then following the warm engine starting procedure listed above. Ensure the ON/ STOP switch is in the ON position. Starting could require pulling the starter rope handle many times depending on how badly the unit is flooded. If engine fails to start, refer to the TROUBLESHOOTING TABLE or call 1-800-554-6723.

CHAIN BRAKE

WARNING: If the brake band is worn too thin it may break when the chain brake is triggered. With a broken brake band, the chain brake will not stop the chain. The chain brake should be replaced by an autho-

rized service dealer if any part is worn to less than 0.020″ (0.5 mm) thick. Repairs on a chain brake should be made by an autho- rized service dealer. Take your unit to the place of purchase if purchased from a ser- vicing dealer, or to the nearest authorized master service dealer.

SThis saw is equipped with a chain brake.

The brake is designed to stop the chain if kickback occurs.

S The inertia--activated chain brake is activated if the front hand guard is pushed forward, either manually (by hand) or automatically (by sudden movement).

S If the brake is already activated, it is disengaged by pulling the front hand guard back toward the front handle as far as possible.

SWhen cutting with the saw, the chain brake must be disengaged.

Disengaged

Engaged

Braking function control CAUTION: The chain brake must be

checked several times daily. The engine must be running when performing this proce- dure. This is the only instance when the saw should be placed on the ground with the en- gine running.

Place the saw on firm ground. Grip the rear handle with your right hand and the front han- dle with your left hand. Apply full throttle by fully depressing the throttle trigger. Activate the chain brake by turning your left wrist against the hand guard without releasing your grip around the front handle. The chain should stop immediately.

Inertia activating function control

WARNING: When performing the following procedure, the engine must be turned off.

Grip the rear handle with your right hand and the front handle with your left hand. Hold the chain saw approximately 14″ (35 cm) above a stump or other wooden surface. Release your grip on the front handle and use the weight of the saw to let the top of the guide bar fall forward and contact the stump. When the tip of the bar hits the stump, the brake should activate.

CUTTING METHODS

IMPORTANT POINTS

SCheck chain tension before first use and

after 1 minute of operation. See CHAIN TENSION in the ASSEMBLY section.

SCut wood only. Do not cut metal, plastics, masonry, non-wood building materials, etc.

SStop the saw if the chain strikes a foreign object. Inspect the saw and repair or re- place parts as necessary.

10

Page 9 Page 11
Page 10
Image 10
Poulan 530164364, 350 instruction manual Cutting Methods, Starting a Warm Engine, Important Points
Page 9 Page 11

530164364, 350 specifications

The Poulan 350,530164364 is a remarkable chainsaw that has made its mark as a reliable tool for both professionals and homeowners. Designed for versatility and ease of use, this chainsaw features a robust engine that delivers consistent power for a variety of cutting tasks.

One of the standout features of the Poulan 350 is its potent 2-stroke engine, which offers a balance of power and efficiency. With a displacement of around 50cc, this chainsaw can handle larger cutting jobs, making it suitable for everything from pruning trees to felling medium-sized ones. The engine is designed to provide high torque at low RPMs, ensuring that users can tackle tough wood without excessive strain on the machine or themselves.

In addition to its powerful engine, the Poulan 350 incorporates advanced technologies that enhance its usability. The chainsaw features an automatic oiling system that lubricates the bar and chain continuously, minimizing wear and ensuring smooth operation. This system is particularly useful during prolonged use, as it helps maintain the cutting performance and prolongs the life of the chain.

Comfort is another key characteristic of the Poulan 350,530164364. The chainsaw is designed with an ergonomic handle that reduces vibrations, allowing users to operate the tool comfortably for extended periods. Additionally, the lightweight construction of the equipment makes it easy to maneuver, reducing fatigue during demanding tasks.

Safety is a priority with this model, which includes several features aimed at protecting the user. The chainsaw is equipped with a chain brake that activates instantly if kickback occurs, stopping the chain's movement to reduce the risk of injury. Moreover, the Poulan 350 comes with a throttle lock that ensures the chainsaw operates only when intended.

Maintenance is simplified with the Poulan 350,530164364, as it features a tool-less access system for the air filter and spark plug. This design allows for quick and hassle-free servicing of the chainsaw, ensuring that it remains in optimal working condition.

In summary, the Poulan 350,530164364 combines power, innovation, and user-friendly features, making it an ideal choice for those looking to tackle a variety of cutting jobs effectively and safely. Whether you're a seasoned professional or a DIY enthusiast, this chainsaw is designed to deliver performance and reliability.
Top Page Image Contents