420497X479, Auger Assembly 30 LH, 420498X479

REPAIR PARTS SNOW THROWER - - MODEL NUMBER XT1053ES (96192002400)

AUGER HOUSING / IMPELLER ASSEMBLY

	KEY	PART	DESCRIPTION
	NO.	NO.	DESCRIPTION
1	1	420497X479	AUGER ASSEMBLY 30 LH
	1	420497X479	AUGER ASSEMBLY 30 LH
	2	420498X479	AUGER ASSEMBLY 30 RH

01.07.019-A

3	01.11.001-A	1

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION

1174762X479 SKID PLATE LH

2178777X479 SKID PLATE RH

372270506 CARRIAGE BOLT 5/16−18 X .75

751153

NUT 5/16−18

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Page 23

Image 23

Poulan XT1053ES, 96192002400, 422077 owner manual 420497X479, Auger Assembly 30 LH, 420498X479, Auger Assembly 30 RH

Contents

Snow Thrower Model Number Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in Carton Remove plastic tie securing rod to lower handle Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See Figs Check Tire Pressure Install Chute Deflector Remote Control See Figs Traction OperationKnow Your Snow Thrower Primer Distance the snow is thrown Meets A.N.S.I. Safety RequirementsDeflector remote control lever used to change Auger control lever used to engage auger motion throw snow Stopping HOW to USE Your Snow Thrower Release the auger control lever and shut off the engine Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Throw Snow See Fig ADD Gasoline See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See Fig If Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before Stopping Lubrication MaintenanceGeneral Recommendations Before Each USE Engine Cleaning Shear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute Deflector To Replace Belts See Fig Other Storage Troubleshooting Exploded KEY Part Description Auger Bearing Auger HousingScrapper BAR CARRIAGEBOLT5/16−18X.625 420498X479 Auger Assembly 30 LHAuger Assembly 30 RH 420497X479 Deflector Seal Deflector Control AssemblyChute Weldment Deflector Weldment Pulley Pivot LEVER/CABLE Rotator AssemblyRotator Head Rotator Pivot Bracket 405784X479 Pivot Support Weldment Loop Handle LHLoop Handle RH Handle Knob SpacerRetainer Knob RED Shifter ROD Bottom Impeller ROD AssemblyTraction ROD Assembly Shifter ROD TOP Flood Headlight Wire HarnessConsole Panel Headlight Bezel Repair Parts Snow Thrower - Model Number XT1053ES Drive Control ARM 43 420900 Drive Plate AssemblyEND Plate Washer 01.03.002-A 417014X505 Engine Mount Plate KEY Part Description ENGINE, TECModel LH358SA-159628A 409346X505 Frame Impeller Belt Belt CoverTraction Belt Cable Bracket LH Cable Bracket RH Repair Parts Snow Thrower - Model Number XT1053ES Wheels Clutch Slide CoverWheel Driver Retainer Ring Wheel Lobe 35062 Safety Ignition KEY DECAL, DANGER, Deflector 181037DECAL, Danger DECAL, Poulan PRO XT 10.5 HP/30 Service Notes Limited Warranty

Poulan XT1053ES, 96192002400 420497X479, Auger Assembly 30 LH, 420498X479, Auger Assembly 30 RH

Models: XT1053ES 422077 96192002400

KEY

420497X479

AUGER ASSEMBLY 30 LH

420498X479

AUGER ASSEMBLY 30 RH

KEY