35062, Safety Ignition KEY | Poulan 422077, 96192002400, XT1053ES

REPAIR PARTS SNOW THROWER - - MODEL NUMBER XT1053ES (96192002400)

BAG OF PARTS

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION
1	198563	POWER CORD
2	169675	RETAINER PIN
3	180684	WRENCH
4	184505	REMOTE SPRING

5179829 SHOULDER BOLT 1/4−20

6179246 NYLON WASHER 1/4−20

7191730 LOCKNUT 1/4−20

4
5	6	7
5

8	9

10 11

1		14
1		13
		13
	12	01.14.003-A
KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION

872250505 CARRIAGE BOLT 5/16−18 X 5/8

9751153 LOCKNUT 5/16−18

1073800600 LOCKNUT 3/8−16

11	19131316	WASHER 3/8
12	198636	SHEAR BOLT 1/4−20 X 1−3/4
13	198638	SPACER
14	73800400	LOCKNUT 1/4−20

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION
1	35062	SAFETY IGNITION KEY

01.14.008-A

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Page 37

Image 37

Poulan 422077, 96192002400, XT1053ES owner manual 35062, Safety Ignition KEY

Contents

Snow Thrower Model Number Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from Carton Unfold Upper Handle Install Speed Control ROD See FigsRemove plastic tie securing rod to lower handle Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See Figs Check Tire Pressure Install Chute Deflector Remote Control See Figs Know Your Snow Thrower OperationPrimer Traction Deflector remote control lever used to change Meets A.N.S.I. Safety RequirementsAuger control lever used to engage auger motion throw snow Distance the snow is thrown Stopping HOW to USE Your Snow Thrower Power Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig Release the auger control lever and shut off the engine Before Starting the Engine To Adjust Skid Plates See FigCheck Engine OIL Level See Fig ADD Gasoline See Fig To Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has Frozen General Recommendations MaintenanceBefore Each USE Lubrication Engine Cleaning To Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See Fig To Replace Belts See Fig Other Storage Troubleshooting Exploded KEY Part Description Scrapper BAR Auger HousingCARRIAGEBOLT5/16−18X.625 Auger Bearing Auger Assembly 30 RH Auger Assembly 30 LH420497X479 420498X479 Chute Weldment Deflector Control AssemblyDeflector Weldment Deflector Seal Rotator Head LEVER/CABLE Rotator AssemblyRotator Pivot Bracket Pulley Pivot Loop Handle RH Loop Handle LH405784X479 Pivot Support Weldment Retainer SpacerKnob RED Handle Knob Traction ROD Assembly Impeller ROD AssemblyShifter ROD TOP Shifter ROD Bottom Console Panel Wire HarnessHeadlight Bezel Flood Headlight Repair Parts Snow Thrower - Model Number XT1053ES Drive END Plate 43 420900 Drive Plate AssemblyWasher Control ARM 01.03.002-A Model LH358SA-159628A KEY Part Description ENGINE, TEC409346X505 Frame 417014X505 Engine Mount Plate Traction Belt Belt CoverImpeller Belt Cable Bracket LH Cable Bracket RH Repair Parts Snow Thrower - Model Number XT1053ES Wheels Wheel Driver Retainer Ring CoverWheel Lobe Clutch Slide 35062 Safety Ignition KEY DECAL, Danger 181037DECAL, Poulan PRO XT 10.5 HP/30 DECAL, DANGER, Deflector Service Notes Limited Warranty

KEY

KEY

WASHER 3/8

SPACER

KEY

35062

SAFETY IGNITION KEY