Manuals / Poulan / Lawn and Garden / Snow Blower

Poulan 422077 Auger Housing, Scrapper BAR, CARRIAGEBOLT5/16−18X.625, Auger Bearing, Bearing Plug

Models: XT1053ES 422077 96192002400

1 40

Download 40 pages 15.37 Kb

Page 22

Image 22

REPAIR PARTS SNOW THROWER - - MODEL NUMBER XT1053ES (96192002400)

AUGER HOUSING / IMPELLER ASSEMBLY

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION
1	404930X505	AUGER HOUSING
2	404933X479	SCRAPPER BAR
3	72270505	CARRIAGEBOLT5/16−18X.625
4	155377	NUT 5/16−18

3 (5x)

4 (5x)

01.07.003-A

2	3

		KEY	PART	DESCRIPTION
		NO.	NO.	DESCRIPTION
		1	420478	AUGER BEARING
3		2	411939	BEARING PLUG
	01.07.024-B	3	179582	SCREW 5/16−18 X 1.00
	01.07.024-B

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Page 22

Image 22

Poulan 422077, 96192002400, XT1053ES Auger Housing, Scrapper BAR, CARRIAGEBOLT5/16−18X.625, Auger Bearing, Bearing Plug

Contents

Model Number Snow Thrower Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from Carton Unfold Upper Handle Install Speed Control ROD See FigsRemove plastic tie securing rod to lower handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See Fig Install Chute Deflector Remote Control See Figs Check Tire Pressure Primer OperationKnow Your Snow Thrower Traction Auger control lever used to engage auger motion throw snow Meets A.N.S.I. Safety RequirementsDeflector remote control lever used to change Distance the snow is thrown HOW to USE Your Snow Thrower Stopping To Throw Snow See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig Release the auger control lever and shut off the engine Check Engine OIL Level See Fig To Adjust Skid Plates See FigBefore Starting the Engine ADD Gasoline See Fig Before Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has Frozen Before Each USE MaintenanceGeneral Recommendations Lubrication Cleaning Engine Chute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See Fig To Replace Belts See Fig Storage Other Troubleshooting Exploded KEY Part Description CARRIAGEBOLT5/16−18X.625 Auger HousingScrapper BAR Auger Bearing 420497X479 Auger Assembly 30 LHAuger Assembly 30 RH 420498X479 Deflector Weldment Deflector Control AssemblyChute Weldment Deflector Seal Rotator Pivot Bracket LEVER/CABLE Rotator AssemblyRotator Head Pulley Pivot Loop Handle RH Loop Handle LH405784X479 Pivot Support Weldment Knob RED SpacerRetainer Handle Knob Shifter ROD TOP Impeller ROD AssemblyTraction ROD Assembly Shifter ROD Bottom Headlight Bezel Wire HarnessConsole Panel Flood Headlight Repair Parts Snow Thrower - Model Number XT1053ES Drive Washer 43 420900 Drive Plate AssemblyEND Plate Control ARM 01.03.002-A 409346X505 Frame KEY Part Description ENGINE, TECModel LH358SA-159628A 417014X505 Engine Mount Plate Traction Belt Belt CoverImpeller Belt Repair Parts Snow Thrower - Model Number XT1053ES Wheels Cable Bracket LH Cable Bracket RH Wheel Lobe CoverWheel Driver Retainer Ring Clutch Slide Safety Ignition KEY 35062 DECAL, Poulan PRO XT 10.5 HP/30 181037DECAL, Danger DECAL, DANGER, Deflector Service Notes Limited Warranty

KEY

AUGER HOUSING

SCRAPPER BAR

CARRIAGEBOLT5/16−18X.625

KEY

AUGER BEARING

BEARING PLUG