Manuals / Poulan / Lawn and Garden / Snow Blower

Poulan PP291EPS27, 96198002900 owner manual Unfold Upper Handle, Install Speed Control ROD See Figs

Models: PP291EPS27 96198002900

1 44

Download 44 pages 57.97 Kb

Page 5

ASSEMBLY / PRE-OPERATION

NOTE: The multi-wrench may be used for assembly of the chute rotator head to snow thrower and making adjustments to the skid plates.

UNFOLD UPPER HANDLE

1.Raise upper handle to the operating position and tighten handle knobs securely. Additional carriage bolts, washers and handle knobs are in bag of parts. Use to secure upper handle to lower handle. Install in lower holes in handles.

INSTALL SPEED CONTROL ROD (See Figs. 1 and 2)

1.Remove plastic tie securing rod to lower handle.

2.Insert rod into speed control bracket and secure with retainer spring.

SPEED

CONTROL

ROD

PLASTIC TIE

UPPER

HANDLE

HANDLE

KNOB

LOWER

HANDLE

FIG. 1

SPEED CONTROL ROD
	RETAINER
	SPRING
SPEED	SPEED
CONTROL	CONTROL
BRACKET	LEVER

FIG. 2

INSTALL TRACTION DRIVE CONTROL ROD (See Figs. 3 and 4)

The traction drive control rod is installed on the snow thrower.

1.Remove plastic tie securing rod to lower handle.

2.With top end of rod positioned under left side of control panel, push rod down and insert top end of rod into hole in drive control bracket. Secure with retainer spring.

PLASTIC TIE

TRACTION DRIVE

CONTROL ROD

VINYL

SLEEVE

FIG. 3

TRACTION DRIVE	RETAINER
CONTROL LEVER	SPRING
	TRACTION
	DRIVE
	CONTROL
	ROD
DRIVE
CONTROL
BRACKET

FIG. 4

5

Image 5

Poulan PP291EPS27 Unfold Upper Handle, Install Speed Control ROD See Figs, Install Traction Drive Control ROD See Figs

Contents

Snow Thrower Model Number Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from Carton Unfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See Figs Check Tire Pressure Install Chute Deflector Remote Control See Figs Know Your Snow Thrower OperationPrimer Ignition KEY Recoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow Thrower Power Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Adjust Skid Plates See Fig To Move Forward and Backward See Fig Scraper BAR See Fig Before Starting the EngineTo USE Drift Cutters See Fig Check Engine OIL Level See Fig To Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has Frozen General Recommendations MaintenanceBefore Each USE Lubrication Engine Cleaning To Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See Fig To Replace Belts See Fig To Remove Wheels See Fig To Adjust Cable Tension See FigCarburetor Engine Speed Other StorageFuel System Engine OIL Troubleshooting Service Notes Exploded KEY Part Description Scraper BAR Auger HousingAuger Bearing Bearing Plug Auger 27 RH Auger 27 LH CARRIAGEBOLT5/16−18X.750 Drift Cutter BARPlastic Washer Lockwasher 5/16 POP Rivet Knob BlackChute Snow Shield Shield Retainer Strap Cable Assembly Adjustable LEVER/CABLE Rotator AssemblyCable Assembly Heat Shield Rotator Head Loop Handle RH Loop Handle LHLower Tube Pivot Support Retainer SpacerKnob RED Handle Knob Traction ROD Assembly Impeller ROD AssemblyShifter ROD TOP Shifter ROD Bottom Console Panel Wire HarnessHeadlight Bezel Flood Headlight Repair Parts Snow Thrower - Model Number PP291EPS27 Drive Exploded Drive Plate Assembly AssemblySpeed Selector Rubber Ring Frame Complete LCT Engine427963X428 Engine Mounting Plate Traction Belt Impeller BeltIdler ARM Bracket Idler Pulley 01.21.014-A Cover Assembly Cable Bracket RH Cable Bracket LH Wheel Driver Retainer Ring CoverWheel Lobe Clutch Slide 422663 Safety Ignition KEY DECAL, Danger 181037DECAL, DANGER, Deflector DECAL, Instruction Service Notes Limited Warranty