NOTE: If the engine sounds as if it is try- ing to start before the 5th pull, stop pulling and immediately proceed to the next step.

6.Push the choke knob in completely (to the OFF position); pull the starter rope until the engine starts.

CHOKE

(SIDE VIEW)

back toward the front handle as far as possible.

SWhen cutting with the saw, the chain brake must be disengaged.

Disengaged

Engaged

Choke knob OFF FULL

7.Allow the engine to run for approximately 5 seconds. Then, squeeze and release throttle trigger to allow engine to return to idle speed.

STARTING A WARM ENGINE:

1.Move ON/STOP switch to the ON posi- tion.

2.Push the choke knob in completely (to the OFF position).

3.Slowly press primer bulb 6 times.

4.Squeeze and hold throttle trigger. With thumb press fast idle lock down; then re- lease throttle trigger.

5.Sharply pull the starter rope with your right hand until the engine starts.

6.Squeeze and release throttle trigger to allow engine to return to idle speed.

DIFFICULT STARTING (or starting a flooded engine):

The engine may be flooded with too much fuel if it has not started after 10 pulls. Flooded engines can be cleared of excess fuel by following the warm engine starting procedure listed above. Insure the ON/ STOP switch is in the ON position. Starting could require pulling the starter rope handle many times depending on how badly the unit is flooded. If engine fails to start, refer to the TROUBLESHOOTING TABLE or call 1-800-554-6723.

CHAIN BRAKE

WARNING: If the brake band is worn too thin it may break when the chain brake is triggered. With a broken brake band, the chain brake will not stop the chain. The chain brake should be replaced by an autho- rized service dealer if any part is worn to less than 0.020″ (0.5 mm) thick. Repairs on a chain brake should be made by an autho- rized service dealer. Take your unit to the place of purchase if purchased from a ser- vicing dealer, or to the nearest authorized master service dealer.

SThis saw is equipped with a chain brake. The brake is designed to stop the chain if

kickback occurs.

S The inertia--activated chain brake is activated if the front hand guard is pushed forward, either manually (by hand) or automatically (by sudden movement).

S If the brake is already activated, it is disengaged by pulling the front hand guard

Braking function control CAUTION: The chain brake must be

checked several times daily. The engine must be running when performing this proce- dure. This is the only instance when the saw should be placed on the ground with the en- gine running.

Place the saw on firm ground. Grip the rear handle with your right hand and the front han- dle with your left hand. Apply full throttle by fully depressing the throttle trigger. Activate the chain brake by turning your left wrist against the hand guard without releasing your grip around the front handle. The chain should stop immediately.

Inertia activating function control

WARNING: When performing the following procedure, the engine must be turned off.

Grip the rear handle with your right hand and the front handle with your left hand. Hold the chain saw approximately 14″ (35 cm) above a stump or other wooden surface. Release your grip on the front handle and use the weight of the saw to let the tip of the guide bar fall forward and contact the stump. When the tip of the bar hits the stump, the brake should activate.

CUTTING METHODS

IMPORTANT POINTS

SCheck chain tension before first use and after 1 minute of operation. See CHAIN

TENSION in the ASSEMBLY section.

SCut wood only. Do not cut metal, plastics, masonry, non-wood building materials, etc.

SStop the saw if the chain strikes a foreign object. Inspect the saw and repair or re- place parts as necessary.

SKeep the chain out of dirt and sand. Even a small amount of dirt will quickly dull a chain

and thus increase the possibility of kickback.

SPractice cutting a few small logs using the following techniques to get the “feel” of us- ing your saw before you begin a major sawing operation.

S Squeeze the throttle trigger and allow the engine to reach full speed before cutting.

S Begin cutting with the saw frame against the log.

S Keep the engine at full speed the en- tire time you are cutting.

10

Page 9 Page 11
Page 10
Image 10
Poulan BH 2160 instruction manual Cutting Methods, Starting a Warm Engine, Important Points
Page 9 Page 11

BH 2160 specifications

The Poulan BH 2160 is a robust and reliable rear-tine tiller designed for both novice gardeners and seasoned horticulturists. With its powerful performance and user-friendly design, the BH 2160 has garnered a positive reputation among outdoor enthusiasts who require an efficient solution for cultivating soil.

At the heart of the Poulan BH 2160 is its potent 208cc four-stroke engine, which delivers ample power to tackle various soil types. The engine is designed for easy starting, ensuring that users can quickly get to work without the frustration of dealing with difficult pull starts. The tiller features a shift-on-the-go transmission with forward and reverse gears, allowing for enhanced maneuverability in tight spaces and making it easier to navigate around flower beds and garden plots.

One of the standout features of the BH 2160 is its robust tilling width. With the capability to till areas up to 16 inches wide, it allows users to cover more ground efficiently in less time. The heavy-duty steel tines dig deep into the soil, churning up stubborn dirt and turning hard ground into ready-to-plant soil. These tines are designed for durability and longevity, ensuring that they can withstand rigorous use over multiple seasons.

Ergonomics play a vital role in the design of the BH 2160, with an adjustable handle that can be tailored to different user heights. This feature promotes comfort during operation, reducing fatigue and enhancing control. The tiller also boasts a lightweight design, making it easier to manage while still providing the sturdy construction needed for tough tilling tasks.

In terms of safety, the Poulan BH 2160 comes equipped with user-friendly controls that are strategically located for easy access, allowing for quick adjustments while in operation. The tiller also features effective safety mechanisms, preventing accidental starts and ensuring that users can work with confidence.

In conclusion, the Poulan BH 2160 is an exceptional rear-tine tiller that expertly combines power, versatility, and ease of use. It is a worthy investment for anyone looking to cultivate their garden with efficiency and reliability. Whether preparing a small backyard garden or tilling larger plots, the BH 2160 provides the necessary power and features to get the job done effectively.
Top Page Image Contents