OPERATION

WARM WEATHER STARTING (50° F and above)

•When engine starts, slowly push choke control in until the engine begins to run smoothly. If the engine starts to run roughly, pull the choke control out slightly for a few seconds and then continue to push the control in slowly.

•The attachments and ground drive can now be used. If the engine does not accept the load, restart the engine and allow it to warm up for one minute using the choke as described above.

COLD WEATHER STARTING (50° F and below)

•When engine starts, slowly push choke control in until the engine begins to run smoothly. Continue to push the choke control in small steps allowing the engine to accept small changes in speed and load, until the choke control is fully in. If the engine starts to run roughly, pull the choke control out slightly for a few seconds and then continue to push the control in slowly. This may require an engine warm-up period from several seconds to several minutes, depending on the temperature.

AUTOMATIC TRANSMISSION WARM UP

•Before driving the unit in cold weather, the transmission should be warmed up as follows:

•Be sure the tractor is on level ground.

•Place the motion control lever in neutral. Release the parking brake and let the clutch/brake slowly return to operating position.

•Allow one minute for transmission to warm up.This can be done during the engine warm up period.

•The attachments can be used during the engine warm-up period after the transmission has been warmed up and may require the choke control be pulled out slightly.

NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32 F) the carburetor fuel mixture may need to be adjusted for best engine performance. See “TO ADJUST CARBURETOR” in the Service and Adjustments section of this manual.

PURGE TRANSMISSION

CAUTION: Never engage or disengage freewheel lever while the engine is run-

ning.

To ensure proper operation and performance, it is recom- mended that the transmission be purged before operating tractor for the first time. This procedure will remove any trapped air inside the transmission which may have de- veloped during shipping of your tractor.

IMPORTANT: SHOULD YOUR TRANSMISSION REQUIRE REMOVAL FOR SERVICE OR REPLACEMENT, IT SHOULD BE PURGED AFTER REINSTALLATION BEFORE OPERATING THE TRACTOR.

•Place tractor safely on level surface with engine off and parking brake set.

•Disengage transmission by placing freewheel control in freewheeling position (See “TO TRANSPORT” in this section of manual).

•Sitting in the tractor seat, start engine. After the engine is running, move throttle control to slow position. With motion control lever in neutral (N) position, slowly dis- engage clutch/brake pedal.

•Move motion control lever to full forward position and hold for five (5) seconds. Move lever to full reverse position and hold for five (5) seconds. Repeat this procedure three (3) times.

NOTE: During this procedure there will be no movement of drive wheels. The air is being removed from hydraulic drive system.

•Move motion control lever to neutral (N) position. Shut- off engine and set parking brake.

•Engage transmission by placing freewheel control in engaged position (See “TO TRANSPORT” in this sec- tion of manual).

•Sitting in the tractor seat, start engine. After the engine is running, move throttle control to half (1/2) speed. With motion control lever in neutral (N) position, slowly disengage clutch/brake pedal.

•Slowly move motion control lever forward, after the tractor moves approximately five (5) feet, slowly move motion control lever to reverse position. After the tractor moves approximately five (5) feet return the motion control lever to the neutral (N) position. Repeat this procedure with the motion control lever three (3) times.

•Your transmission is now purged and now ready for normal operation.

MOWING TIPS

•Mower should be properly leveled for best mowing per- formance. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual.

•The left hand side of mower should be used for trim- ming.

•Drive so that clippings are discharged onto the area that has been cut. Have the cut area to the right of the machine. This will result in a more even distribution of clippings and more uniform cutting.

•When mowing large areas, start by turning to the right so that clippings will discharge away from shrubs, fences, driveways, etc. After one or two rounds, mow in the opposite direction making left hand turns until finished (See Fig. 12).

FIG. 12

•If grass is extremely tall, it should be mowed twice to reduce load and possible fire hazard from dried clip- pings. Make first cut relatively high; the second to the desired height.

•Do not mow grass when it is wet. Wet grass will plug mower and leave undesirable clumps. Allow grass to dry before mowing.

•Always operate engine at full throttle when mow- ing to assure better mowing performance and proper discharge of material. Regulate ground speed by selecting a low enough gear to give the mower cutting performance as well as the quality of cut desired.

•When operating attachments, select a ground speed that will suit the terrain and give best performance of

15the attachment being used.

Page 14 Page 16
Page 15
Image 15
Poulan DB27H48YT manual Mowing Tips, Purge Transmission, Automatic Transmission Warm UP
Page 14 Page 16

DB27H48YT specifications

The Poulan DB27H48YT is a robust, high-performance lawn tractor that stands out in the market for home gardening and yard maintenance. Known for its versatility and reliability, this model is particularly aimed at homeowners with medium to large yards, offering an excellent balance between power and user-friendliness.

One of the main features of the Poulan DB27H48YT is its powerful 27 HP Briggs & Stratton engine, which ensures optimal performance for various mowing tasks. The engine is designed with improved efficiency and durability in mind, providing homeowners with a dependable solution for their lawn care needs. The automatic transmission enhances ease of use, allowing operators to shift gears seamlessly without the hassle of manual clutching.

The 48-inch cutting deck is another noteworthy characteristic, featuring five adjustable cutting heights that range from 1.5 to 4 inches. This flexibility allows users to customize their mowing experience based on grass conditions and personal preferences, ensuring an even and precise cut across different types of terrain. The deck is constructed from high-quality material, designed to withstand the rigors of regular use and provide a long-lasting lifespan.

Incorporating advanced mowing technologies, the Poulan DB27H48YT is equipped with a debris shield and a mulching kit option. These features not only enhance the mowing experience but also contribute to improved lawn health by returning nutrients back into the soil. Additionally, the tractor's side discharge chute allows for efficient grass clipping management.

User comfort is taken into consideration with a plush, adjustable seat and an ergonomic steering wheel, ensuring a comfortable ride even during extended mowing sessions. The easy-to-access control panel is designed for effortless operation, making it suitable for users of all skill levels.

Other characteristics of the Poulan DB27H48YT include rugged tires that provide excellent traction on various terrains and a convenient fuel gauge for monitoring gas levels. The model also boasts a sturdy frame and construction, ensuring stability and longevity, making it an investment worth considering for any homeowner looking to simplify lawn care.

Overall, the Poulan DB27H48YT combines power, advanced technology, and user-friendly features to deliver an exceptional lawn tractor that meets the demands of modern gardening.
Top Page Image Contents