OPERATION

TO ADJUST SKID PLATES (See Fig. 17)

NOTE: The wrench provided in your parts bag may be used to adjust the skid plates.

Skid plates are located on each side of the auger housing and adjust the clearance between the scraper bar and the ground surface. Adjust skid plates evenly to proper height for current surface conditions. For removal of snow in normal conditions, such as a paved driveway or sidewalk, place skid plates in the highest position (lowest scraper clearance) to give a 1/8" clearance between the scraper bar and the ground. Use a middle position if the surface to be cleared is uneven.

NOTE: It is not recommended to operate the snow thrower over gravel or rocky surfaces. Objects such as gravel, rocks or other debris, can easily be picked up and thrown by the impeller, which can cause serious personal injury, property damage or damage to the snow thrower.

•If snow thrower must be operated over gravel surface, use extra caution and be sure skid plates are adjusted to lowest (highest scraper clearance) position.

1.Shut off engine and wait for all moving parts to stop.

2.Adjust skid plates by loosening the rear 1/2" hex nut only, then moving skid plate to desired position.Be sure both plates are adjusted evenly. Tighten securely.

HIGH POSITION (LOW GROUND CLEARANCE)

AUGER

HOUSING

SKID PLATE

1/2" HEX NUT

LOW POSITION (HIGH GROUND CLEARANCE)

FIG. 17

SCRAPER BAR

The scraper bar is not adjustable, but is reversible. After considerable use it may become worn. When it has worn almost to the edge of the housing, it can be reversed, providing additional service before requiring replacement. Replace a damaged or worn scraper bar.

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL (See Fig. 18)

The engine on your snow thrower has been shipped, from the factory, already filled with oil.

1.Check engine oil with snow thrower on level ground.

2.Remove oil fi ll cap/dipstick and wipe clean, reinsert the dipstick and screw tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill.

•To change engine oil, see “TO CHANGE ENGINE OIL” in the Maintenance section of this manual.

ADD GASOLINE (See Fig. 18)

•Fill fuel tank to bottom of tank fi ller neck. Do not over- fill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30

days to assure fuel freshness.

12

WARNING: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can at- tract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

CHOKE CONTROL

THROTTLE PRIMER ENGINE OIL

 

FILL CAP /

 

DIPSTICK

SAFETY

IGNITION

KEY

 

GASOLINE

 

FILLER CAP

 

FUEL SHUT-

 

OFF VALVE

RECOIL

STARTER BUTTON

STARTER

 

HANDLE

POWER CORD PLUG

NOTE: ALL ITEMS ARE SHOWN IN THEIR TYPICAL LOCATION. ACTUAL LOCATION MAY VARY WITH ENGINE ON YOUR UNIT.

FIG. 18

TO START ENGINE

•Be sure fuel shut-off valve is in the OPEN position.

Your snow thrower engine is equipped with both a 120 Volt A.C. electric starter and a recoil starter. The electric starter is equipped with a three-wire power cord and plug and is designed to operate on 120 Volt A.C. household current.

•Be sure your house is a 120 Volt A.C. three-wire grounded system. If you are uncertain, consult a licensed electrician.

WARNING: Do not use the electric starter if your house is not a 120 Volt A.C. three-wire grounded system. Se- rious personal injury or damage to your snow thrower could result.

Page 11 Page 13
Page 12
Image 12
Poulan P524ESA owner manual Before Starting the Engine, Scraper BAR, To Start Engine
Page 11 Page 13

P524ESA specifications

The Poulan P524ESA is a reliable and efficient snow thrower designed to tackle winter's harshest conditions with ease. This powerful machine blends advanced technology with user-friendly features, making it an excellent choice for homeowners and professionals alike.

At the heart of the Poulan P524ESA is its robust 24-inch clearing width and 20-inch intake height, allowing it to clear large amounts of snow in a single pass. Powered by a 208cc engine, this snow thrower delivers impressive performance, capable of moving heavy, compacted snow effectively. The engine is designed for easy starting, ensuring that users can quickly get to work, even in the frigid winter temperatures.

One of the standout features of the P524ESA is its electric start capability, which allows users to start the machine with the push of a button. This convenience eliminates the frustration often associated with pull-start engines, especially in cold weather. The snow thrower also includes an easy-to-use recoil start as a backup option.

The P524ESA boasts a 2-speed forward and 1-speed reverse transmission, giving users the flexibility to adjust their speed based on snow conditions and terrain. This versatility ensures better control and maneuverability, especially in tight spaces around driveways, sidewalks, and patios.

Another key characteristic of the Poulan P524ESA is its durable construction. The strong steel housing and auger system are designed to withstand the rigors of heavy snowfall, while the heavy-duty rubber auger is efficient in breaking down and throwing snow. The adjustable chute deflector allows users to control the direction and distance the snow is thrown, making it easy to keep walkways and driveways clear.

In terms of comfort, the P524ESA is equipped with ergonomic handles and easily accessible controls, ensuring that operators can use it with minimal strain. The snow thrower also features integrated headlights for visibility during early morning or late evening snow clearing, adding to its practicality.

Overall, the Poulan P524ESA is a well-rounded snow thrower that combines power, efficiency, and user-friendly features. With its reliable engine, adjustable settings, and durable build, it's designed to make winter snow removal a breeze, allowing users to enjoy the season without the burden of heavy snowfall.
Top Page Image Contents