OPERATION

WARM WEATHER STARTING (50°F (10°C) and above)

•When engine starts, move the throttle control to the fast position.

•The attachments and ground drive can now be used. If the engine does not accept the load, restart the engine and allow it to warm up for one minute using the choke as described above.

COLD WEATHER STARTING (50°F (10°C) and below)

•When engine starts, allow engine to run with the throttle control in the choke position until the engine runs rough- ly, then move throttle control to fast position. This may require an engine warm-up period from several seconds to several minutes, depending on the temperature.

AUTOMATIC TRANSMISSION WARM UP

•Before driving the unit in cold weather, the transmission should be warmed up as follows:

•Be sure the tractor is on level ground.

•Place the motion control lever in neutral. Release the parking brake and let the clutch/brake slowly return to operating position.

•Allow one minute for transmission to warm up. This can be done during the engine warm up period.

•Theattachmentscanalsobeusedduringtheenginewarm- up period after the transmission has been warmed up.

NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32° F(0°C) the carburetor fuel mixture may need to be adjusted for best engine performance. See “TO ADJUST CARBURETOR” in the Service and Adjust- ments section of this manual.

PURGE TRANSMISSION

CAUTION: Never engage or disengage the freewheelleverwhiletheengineisrunning.

To ensure proper operation and performance, it is recom- mended that the transmission be purged before operating tractor for the first time. This procedure will remove any trapped air inside the transmission which may have de- veloped during shipping of your tractor.

IMPORTANT: SHOULD YOUR TRANSMISSION REQUIRE REMOVAL FOR SERVICE OR REPLACEMENT, IT SHOULD BE PURGED AFTER REINSTALLATION BEFORE OPERATING THE TRACTOR.

1.Place tractor safely on a level surface - that is clear and open - with engine off and parking brake set.

2.Disengage transmission by placing freewheel control in freewheeling position (See “TO TRANSPORT” in this section of manual).

3.Sitting in the tractor seat, start engine. After the engine is running, move throttle control to slow position. With motion control lever in neutral position, slowly disengage clutch/brake pedal.

CAUTION: At any time, during step 4, there may be movement of the drive wheels.

4.Move motion control lever to full forward position and hold for five (5) seconds. Move lever to full reverse position and hold for five (5) seconds. Repeat this procedure three (3) times.

5.Move motion control lever to neutral position. Shut- off engine and set parking brake.

6.Engage transmission by placing freewheel control in engaged position (See “TO TRANSPORT” in this sec- tion of manual).

7.Sitting in the tractor seat, start engine. After the engine is running, move throttle control to half (1/2) speed. With motion control lever in neutral position, slowly disengage clutch/brake pedal.

8.Slowly move motion control lever forward, after the tractor moves approximately five (5) feet, slowly move motion control lever to reverse position. After the trac- tor moves approximately five (5) feet return the motion control lever to the neutral position. Repeat this proce- dure with the motion control lever three (3) times.

Your transmission is now purged and now ready for normal operation.

MOWING TIPS

•Tire chains cannot be used when the mower housing is attached to tractor.

•Mower should be properly leveled for best mowing performance. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual.

•The left hand side of mower should be used for trimming.

•Drive so that clippings are discharged onto the area that has been cut. Have the cut area to the right of the tractor. This will result in a more even distribution of clippings and more uniform cutting.

•When mowing large areas, start by turning to the right so that clippings will discharge away from shrubs, fences, driveways, etc. After one or two rounds, mow in the opposite direction making left hand turns until finished (See Fig. 15).

Fig. 15

•If grass is extremely tall, it should be mowed twice to reduce load and possible fire hazard from dried clip- pings. Make first cut relatively high; the second to the desired height.

•Do not mow grass when it is wet. Wet grass will plug mower and leave undesirable clumps. Allow grass to dry before mowing.

•Always operate engine at full throttle when mow- ing to assure better mowing performance and proper discharge of material. Regulate ground speed by selecting a low enough gear to give the mower cutting performance as well as the quality of cut desired.

•When operating attachments, select a ground speed that will suit the terrain and give best performance of the attachment being used.

13

Page 12 Page 14
Page 13
Image 13
Poulan PB195H42LT warranty Mowing Tips, Purge Transmission, Automatic Transmission Warm UP
Page 12 Page 14

PB195H42LT specifications

The Poulan PB195H42LT is a robust riding lawn mower designed to provide an efficient and enjoyable mowing experience. With an impressive blend of power, durability, and advanced features, this mower caters to homeowners with substantial lawn care needs.

At the heart of the PB195H42LT is its reliable 195cc Briggs & Stratton engine. This engine is known for its durability and consistent performance, allowing for effortless starts and smooth operation. The engine provides ample power to tackle tough grass and uneven terrain, ensuring a clean and even cut every time.

One of the standout features of the Poulan PB195H42LT is its 42-inch cutting deck. This wide mowing deck enables users to cover larger areas in less time while providing a clean cut. The deck is designed with an innovative cutting system that utilizes two sharp blades, which not only promotes a fine finish but also helps in mulching grass clippings effectively.

The mower also boasts a 6-position cutting height adjustment feature, allowing users to customize their lawn mowing experience. Whether you're looking for a close trim or a higher cut, the adjustable heights suit various grass types and conditions, providing flexibility for different lawn care tasks.

The PB195H42LT incorporates a foot-controlled hydrostatic transmission that delivers seamless speed changes. This technology allows for smooth acceleration and deceleration without the need for shifting gears. As a result, operators can navigate their yards with precision and comfort, especially around obstacles such as flower beds and trees.

Comfort is a priority in the design of the PB195H42LT. The mower features an ergonomic seat with ample cushioning, ensuring a pleasant riding experience, even during extended mowing sessions. Additionally, the easy-to-use controls are conveniently located for quick adjustments, minimizing distractions when operating the machine.

Safety is also a significant consideration with this mower. It includes features such as an operator presence system that ensures the engine shuts off if the operator leaves the seat, thereby preventing accidents.

In summary, the Poulan PB195H42LT combines powerful performance with user-friendly design. With its efficient engine, versatile cutting deck, flawless transmission system, and comfortable features, this riding lawn mower is an ideal choice for homeowners who prioritize quality and efficiency in lawn maintenance. Its reliable construction and innovative technology make it a valuable addition to any gardening toolkit.
Top Page Image Contents