Replace the old chain when it becomes worn or damaged. Use only the Low-Kickback replace- ment chain specified in the repair parts list.

TO REPLACE CHAIN:

1.Move ON/OFF switch to the OFF position and disconnect spark plug.

2.Remove bar clamp nut.

3.Remove bar clamp.

4.Turn adjusting screw by hand counter- clockwise until adjusting pin just touches the stop.

5.Slide guide bar behind sprocket until guide bar stops against sprocket.

6.Remove the old chain.

7.Carefully remove new chain from pack- age. Hold chain with the drive links as shown.

Cutter

Tip of

Bar

Drivelink

CUTTERS MUST FACE IN

DIRECTION OF ROTATION

Cutters

Depth Gauge

 

Drive Links

8.Place chain over sprocket, fitting the drive links in the sprocket.

9.Fit bottom of drive links between the teeth in the sprocket in the nose of the guide bar.

10.Fit chain drive links into bar groove.

11.Pull guide bar forward until chain is snug in guide bar groove. Ensure all drive links are in the bar groove.

12.Now, install bar clamp making sure the adjusting pin is positioned in the lower hole in the guide bar.

Lower

Hole

Adjusting Pin

Guide Bar

13.Install bar clamp nut and finger tighten only. Do not tighten any further at this point. Proceed to the CHAIN ADJUST- MENT section.

CHAIN ADJUSTMENT

See CHECK CHAIN TENSION in MAINTE- NANCE section.

CARBURETOR ADJUSTMENT

WARNING: Keep others away when making idle speed adjustments. The chain will be moving during most of this procedure. Wear your protective equipment and observe all safety precautions. After making adjust- ments, the chain must not move at idle speed. The carburetor has been carefully set at the factory. Adjustment to the idle speed may be necessary if you notice any of the following conditions:

SEngine will not idle when the throttle is re- leased.

SThe chain moves at idle.

Make adjustments with the unit supported so the pruner is off the ground and the chain will not make contact with any object. Hold the unit by hand while running and making adjust- ments. Keep all parts of your body away from the chain and muffler.

Idle Speed Adjustment

Allow engine to idle. Adjust idle speed until en- gine runs without chain moving (idle too fast) or stalling (idle speed too slow).

S Turn idle speed screw clockwise to in- crease engine speed if engine stalls or dies.

S Turn idle speed screw counterclockwise to decrease engine speed if chain moves at idle.

WARNING: Recheck the idle speed after each adjustment. The chain must not move at idle speed to avoid serious injury to the operator or others.

Idle Speed Screw

Air Filter Cover

If you require further assistance or are unsure about performing this procedure, contact your authorized service dealer or call 1--800--554--6723.

15

Page 14 Page 16
Page 15
Image 15
Poulan PP258TP instruction manual To Replace Chain, Chain Adjustment, Carburetor Adjustment
Page 14 Page 16

PP258TP specifications

The Poulan PP258TP is a versatile and powerful pole saw that caters to both homeowners and landscaping professionals alike. Designed for efficient tree trimming and maintenance tasks, this tool combines robust performance with user-friendly features, making it an ideal choice for anyone looking to keep their outdoor spaces well-groomed.

One of the standout features of the PP258TP is its 25cc, 2-cycle engine. This powerful engine delivers strong performance while also being lightweight, allowing users to maneuver the pole saw with ease. The engine is designed to start quickly, reducing frustration and enabling users to focus on their work rather than struggling with difficult starts.

The Poulan PP258TP also comes equipped with a 10-inch Oregon bar and chain, which allows for precise cutting. This saw is suitable for reaching high branches without the need for a ladder, thanks to its adjustable extension pole that can extend up to 8 feet. This added reach is particularly useful for tackling tall trees and hard-to-reach areas, making it a valuable tool for any yard maintenance task.

In terms of technology, the PP258TP showcases Poulan's commitment to user comfort and safety. The tool features an anti-vibration system that helps reduce fatigue during prolonged use, allowing users to work longer while maintaining comfort. Additionally, a safety switch ensures that the tool only operates when intended, providing an extra layer of security, especially when working on elevated branches.

Durability is another key characteristic of the Poulan PP258TP. Built with high-quality materials, this pole saw is designed to withstand the rigors of outdoor use. The bar and chain are engineered for longevity, and regular maintenance protocols ensure continued optimal performance.

Finally, the lightweight design of the PP258TP makes it easy to carry and handle. Weighing just over 10 pounds, it strikes a balance between power and portability, making it a reliable choice for both occasional users and professionals who require efficiency and ease of use.

In conclusion, the Poulan PP258TP pole saw stands out for its combination of power, reach, and user-friendly features. With its robust engine, long extension capability, anti-vibration technology, and durable construction, it is an exceptional tool for effective outdoor maintenance. Whether you're pruning branches or clearing overgrowth, the PP258TP delivers reliable performance, ensuring a well-kept landscape with minimal hassle.
Top Page Image Contents