BEFORE STARTING ENGINE

WARNING: Be sure to read the fuel handling information in the safety rules sec- tion of this manual before you begin. If you do not understand the fuel handling information do not attempt to fuel your unit. Seek help from someone that does understand the in- formation or call the customer assistance help line at 1-800-554-6723.

FUELING ENGINE

WARNING: Remove fuel cap slow- ly when refueling.

HELPFUL TIP

To obtain the correct oil mix ratio, pour 3.2 ounces of 2-cycle synthetic oil into one gallon of fresh gas.

This engine is certified to operate on un- leaded gasoline. Before operation, gasoline must be mixed with a good quality synthetic 2-cycle air-cooled engine oil designed to be mixed at a ratio of 40:1. Poulan/WEED EATER brand synthetic oil is recommended. A 40:1 ratio is obtained by mixing 3.2 ounces (95 ml) of oil with 1 gallon (4 liters) of un- leaded gasoline. Included with this saw is a

3.2ounce (95 ml) container of Poulan/Weed Eater brand synthetic oil. Pour the entire contents of this container into 1 gallon (4 li- ters) of gasoline to achieve the proper fuel mixture.

DO NOT USE automotive or marine oil. These oils will cause engine damage. When mixing fuel follow the instructions printed on the container. Always read and follow the safety rules listed under HANDLE FUEL WITH CAUTION.

BAR AND CHAIN LUBRICATION

The bar and chain require continuous lubri- cation. Lubrication is provided by the auto- matic oiler system when the oil tank is kept filled. Lack of oil will quickly ruin the bar and chain. Too little oil will cause overheating shown by smoke coming from the chain and/ or discoloration of the bar.

In freezing weather oil will thicken, making it necessary to thin bar and chain oil with a small amount (5 to 10%) of #1 Diesel Fuel or kerosene. Bar and chain oil must be free flowing for the oil system to pump enough oil for adequate lubrication.

Genuine Poulan or Poulan PRO bar and chain oil is recommended to protect your unit against excessive wear from heat and fric- tion. Poulan or Poulan PRO oil resists high temperature thinning.

If Poulan or Poulan PRO bar and chain oil is not available, use a good grade SAE 30 oil.

SNever use waste oil for bar and chain lubri-

cation.

SAlways stop the engine before removing the oil cap.

IMPORTANT

Experience indicates that alcohol--blended fuels (called gasohol or using ethanol or meth-

anol) can attract moisture which leads to sepa- ration and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine prob- lems, the fuel system should be emptied before storage for 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See STORAGE section for addi- tional information.

CHAIN BRAKE

Ensure chain brake is disengaged by pulling the front hand guard back toward the front han- dle as far as possible. The chain brake must be disengaged before cutting with the saw.

WARNING: The chain must not move when the engine runs at idle speed. If the chain moves at idle speed refer to CAR- BURETOR ADJUSTMENT within this manual. Avoid contact with the muffler. A hot muffler can cause serious burns.

To stop the engine move the ON/STOP switch to the STOP position.

To start the engine hold the saw firmly on the ground as illustrated. Make sure the chain is free to turn without contacting any object.

Use only 15″ -- 18″ (40 -- 45 cm) of rope per pull.

Hold saw firmly while pulling starter rope. Starter Rope Handle

Left Hand on Front Handle

Right Foot Through Rear Handle

IMPORTANT POINTS TO REMEMBER

When pulling the starter rope, do not use the full extent of the rope as this can cause the rope to break. Do not let starter rope snap back. Hold the handle and let the rope re- wind slowly.

For cold weather starting, start the unit at FULL CHOKE; allow the engine to warm up before squeezing the throttle trigger.

NOTE: Do not attempt to cut material with the choke/fast idle lever in the FULL CHOKE position.

HELPFUL TIP

If your engine still does not start after following these instructions, please call 1-800-554-6723.

STARTING A COLD ENGINE (or warm engine after running out of fuel)

NOTE: In the following steps, when the choke/fast idle lever is pulled out to the full extent, the correct throttle setting for starting is set automatically.

9

Page 8 Page 10
Page 9
Image 9
Poulan PP3816AV, PP4218AV, PP4218AVL instruction manual Before Starting Engine Fueling Engine, BAR and Chain Lubrication
Page 8 Page 10

PP3816AV, PP4218AV, PP4218AVL specifications

The Poulan brand has established itself as a reliable name in the realm of outdoor power equipment, with a solid reputation for producing efficient and durable chainsaws. Among its notable models are the Poulan PP3816AV, PP4218AV, and PP4218AVL, each designed to cater to diverse cutting needs while incorporating advanced technologies and features to enhance user experience.

The Poulan PP3816AV model is compact and lightweight, making it ideal for both novices and seasoned users. It features a powerful 38cc two-stroke engine that provides ample cutting power for small to medium-sized trees, as well as for trimming branches. The 16-inch bar and chain allow for precise cuts, while the patented AV (Anti-Vibration) technology minimizes user fatigue during extended use. Additionally, the easy-access chain tensioning system simplifies adjustments, ensuring optimal chain performance.

Progressing to the PP4218AV, this model offers increased power with its 42cc engine, making it suitable for larger cutting tasks and demanding environments. It retains the 18-inch bar and chain, providing extended reach for tackling higher branches and thicker logs. The anti-vibration system is also present in this model, enhancing comfort during operation. Furthermore, the PP4218AV includes an Easy Start technology that reduces resistance and makes starting the engine effortless, even after long periods of inactivity.

The Poulan PP4218AVL takes things a step further with its enhanced features and capabilities. This model combines the power of a 42cc engine with advanced air filtration, ensuring maximum engine life and optimal performance in dusty environments. The 18-inch Oregon bar and chain guarantee smooth and efficient cuts, while the automatic oiler system keeps the chain adequately lubricated, reducing wear and enhancing durability. The lightweight design and improved anti-vibration system ensure that users can handle this chainsaw for extended periods without discomfort.

In summary, the Poulan PP3816AV, PP4218AV, and PP4218AVL chainsaws embody a blend of power, efficiency, and user-friendliness. With their respective engine sizes and bar lengths, they cater to a range of cutting requirements, from light pruning to more heavy-duty tasks. Each model embraces advanced technologies, such as anti-vibration systems and easy start features, making them excellent choices for both landscaping enthusiasts and professionals alike. With Poulan’s commitment to quality and innovation, users can depend on these chainsaws to get the job done reliably and efficiently.
Top Page Image Contents