SERVICE AND ADJUSTMENTS

FRONT-TO-BACK ADJUSTMENT (See Figs. 21 and 22)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO-SIDE.

To obtain the best cutting results, the mower housing should be adjusted so the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its highest position.

Check adjustment on right side of tractor. Measure dis- tance “F” directly in front of and behind the mandrel at bottom edge of mower housing as shown.

Before making any necessary adjustments, check that both front links are equal in length.

If links are not equal in length, adjust one link to same length as other link.

To lower front of mower housing, loosen nut “G” on both front links an equal number of turns.

When distance “F” is 1/8" to 1/2" lower at front than rear, tighten nut “H” against trunnion on both front links.

To raise front of mower housing, loosen nut “H” from trunnion on both front links. Tighten nut “G” on both front links an equal number of turns.

When distance “F” is 1/8" to 1/2" lower at front than rear, tighten nut “H” against trunnion on both front links.

NOTE: Each full turn of nut “G” will change dim. “F” by approximately 3/8".

Recheck side-to-side adjustment.

MANDREL

“F”

“F”

FIG. 21

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

NUT “H”

NUT “G”

TRUNNION

 

 

FRONT PLATE

 

ASSEMBLY

FIG. 22

TO REPLACE MOWER DRIVE BELT

MOWER DRIVE BELT REMOVAL (See Fig. 23)

Park tractor on a level surface. Engage parking brake.

Remove screws from L.H. mandrel cover and remove cover.

Roll belt over the top of L.H. mandrel pulley.

Remove belt from electric clutch pulley.

Remove belt from idler pulleys.

Remove any dirt or grass clippings which may have accumulated around mandrels and entire upper deck surface.

Check primary idler arm and two idlers to see that they rotate freely.

Be sure spring is securely hooked to primary idler arm and bolt in mower housing.

MOWER DRIVE BELT INSTALLATION (See Fig. 23)

Install belt in both idlers. Make sure belt is in both belt keepers at the idlers as shown.

Install new belt onto electric clutch pulley.

Roll belt into upper groove of L.H. mandrel pulley.

Carefully check belt routing making sure belt is in the grooves correctly and inside belt keepers.

Reassemble L.H. mandrel cover.

L.H.

SCREWS

 

 

ELECTRIC

IDLER

SPRING

CLUTCH

MANDREL

 

PULLEY

 

 

COVER

 

 

PULLEYS

 

 

 

 

 

PRIMARY

 

 

 

 

 

IDLER ARM

 

 

 

 

 

 

BOLT IN

 

 

 

 

 

MOWER

 

 

 

 

 

HOUS-

L.H.

 

 

 

 

ING

 

 

 

 

 

MANDREL

 

 

 

 

 

MOWER

 

 

 

 

 

DRIVE

BELT

 

 

 

 

BELT

 

 

 

 

 

KEEPERS

 

 

FIG. 23

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 24)

Park the tractor on level surface. Engage parking brake.

Remove mower drive belt (See “TO REPLACE MOWER DRIVE BELT” in this section of this manual).

Remove mower (See “TO REMOVE MOWER” in this section of this manual).

Remove screws from R.H. mandrel cover and remove cover. Unhook spring from bolt on mower housing.

Carefully roll belt off R.H. mandrel pulley.

Remove belt from center mandrel pulley, idler pulley, and L.H. mandrel pulley.

Remove any dirt or grass which may have accumulated

21around mandrels and entire upper deck surface.

Page 21
Image 21
Poulan PRGT22H50D owner manual To Replace Mower Drive Belt, To Replace Mower Blade Drive Belt See Fig

PRGT22H50D specifications

The Poulan PRGT22H50D is a standout in the realm of outdoor power equipment, specifically designed for homeowners seeking a reliable and efficient lawn tractor. Renowned for its robust features and user-friendly design, the PRGT22H50D delivers exceptional performance for lawn care enthusiasts.

One of the key features of this lawn tractor is its powerful 22-horsepower engine, providing ample horsepower to tackle even the toughest grass. This engine is engineered for durability and efficiency, allowing users to cover more ground at an impressive speed. The tractor is equipped with a 50-inch cutting deck, offering a wide cutting path that reduces the time spent mowing. The cutting deck design allows for superior grass dispersion, leaving a well-manicured lawn in its wake.

The PRGT22H50D incorporates a hydrostatic transmission, which provides a smooth and effortless driving experience. This type of transmission allows for seamless speed changes without the need for gear shifting, making it user-friendly for operators of all experience levels. The intuitive controls are strategically placed, allowing for easy maneuverability around obstacles, ensuring that every inch of grass is trimmed with precision.

Comfort is at the forefront of the design, featuring an adjustable high-back seat that promotes better posture and reduces fatigue during longer mowing sessions. Additionally, the lawn tractor includes a steering wheel that is ergonomically designed for ease of use, enhancing the overall comfort of the operator.

Another notable technology in the Poulan PRGT22H50D is its cutting height adjustment feature, which allows users to customize the height of their cut with ease. This versatility ensures that homeowners can achieve the ideal grass length for their specific lawn needs.

Safety features are also integrated into the design, with a built-in safety switch that helps prevent accidental starts when the operator is not in the seat. This attention to safety reflects Poulan’s commitment to ensuring a secure mowing experience.

Overall, the Poulan PRGT22H50D is an impressive lawn tractor that marries power, comfort, and cutting-edge technology, making it an ideal choice for any homeowner looking to maintain their lawn efficiently and effectively. Whether for small yards or larger properties, this tractor promises to deliver a reliable performance that meets the demands of modern lawn care.