INSTALLATION GUIDE: XUF-3760
Victory Flat Screen Wall Mounting System
Included
Hardware
Universal Washer | 3” Lag Bolts | |
(Qty 8) | (Qty 6) | |
Flat Washers (Qty 6) | NOTE: To correctly determine your hardware, please refer | |
to the hardware list below. | ||
|
The Victory Flat Screen Wall Mounting System is designed for secure installation of flat screen displays up to 60”.
Warning Statements
WARNING: THE WALL STRUCTURE MUST BE CAPABLE OF SUPPORTING AT LEAST A MINIMUM WEIGHT OF 350LBS. IF NOT, THE WALL MUST BE REINFORCED. PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN, AS OUTLINED IN THE INSTALLATION INSTRUCTIONS, MUST BE ADHERED TO. FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY OR EVEN DEATH. DO NOT PLACE A UNIT WEIGHING MORE THAN 175LBS. ON THIS UNIT.
WARNING: SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE INSTALLATION OF THIS PRODUCT. USE PROPER SAFETY GEAR AND TOOLS FOR THE INSTALLATION PROCEDURE TO PREVENT PERSONAL INJURY.
1/4" Nylon spacers
(large) (Qty 6)
1/2" Nylon spacers
(large) (Qty 12)
5/16" Flat washers
(metal) (Qty 6)
1/4" Nylon spacers (small)
(Qty 6)
9/16" Nylon spacers (Qty 6)
Nylon sleeves (Qty 4)
M4 x 16 
(Qty 8)
M4 x 25 |
|
|
|
|
| (Qty 4) | ||
|
|
|
|
| ||||
|
|
|
| (Qty 8) | ||||
M5 x 12 |
|
|
|
| ||||
|
|
|
|
|
| (Qty 6) | ||
M5 x 16 |
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| (Qty 6) |
M5 x 20 |
|
|
|
|
|
|
| |
M5 x 25 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
M5 x 50 |
|
|
|
|
|
|
|
|
M6 x 12 |
|
|
| (Qty 8) | ||||
|
|
| ||||||
|
|
|
|
|
|
|
|
|
M6 x 20
M6 x 30
M8 x 20
M8 x 25
M8 x 30
(Qty 4)
M8 x 35
M8 x 70
(Qty 6)
(Qty 6)
(Qty 6)
(Qty 6)
(Qty 6)
(Qty 4)
(Qty 4)
WARNING: PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION INSTRUCTIONS SHOULD BE READ AND COMPLETELY UNDERSTOOD. THE INSTALLATION INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL INJURY AND PROPERTY DAMAGE. KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE.
A secure structure must support the weight, or load, of the display. When mounting to a wall that contains wooden studs, dead center of the wooden stud must be confirmed prior to installation.
Do not install on a structure that is prone to vibration, movement or chance of impact. Failure to do so could result in damage to the display and/or damage to the mounting surface.
Do not install near heater, fireplace, direct sunlight, air conditioning or any other source of direct heat energy. Failure to do so may result in damage to the display and could increase the risk of fire.
At least two qualified people should perform the installation procedure. Injury and/or damage can result from dropping or mishandling the display.
Recommended mounting surfaces: wooden studs and
Contact
Tool List
Phillips Head Screw Driver Electronic Stud Finder ½” Socket and Wrench Portable Drill
Masonry Bit for Concrete Installation 1/4” Drill Bit for Wood Installations Level (Commercially Available)
SECURE THE PLATE TO THE WALL
1.Begin by removing all pieces of the Wall Mounting System to ensure that you have all the necessary parts.
2.Instructions for mounting will vary slightly depending on your wall construction.
Wood Stud Mounting
1. For secure wood stud mounting, the wall plate must beLag Bolt and Washer mounted to two studs at least 16” apart.
2.Use a
3.With the help of an assistant, use a level (commercially available) and position the wall plate against the wall in the desired mounting location.
4.Mark the right, upper and lower and the left (upper and lower), positions of the small horizontal slots that are in alignment with the studs.
5.You should mark four positions total.
6.Next,
Continued on back page
