Proficient Audio Systems M4 quick start

1514

M4 QUICK START GUIDE

M4 SpECIfICATIonS

For technical inquiries, please call 877.888.9004 or email us at

techsupport@proficientaudio.com. We are available to assist you every

weekday, except holidays, between the hours of 7:00 a.m. and 5:0 0 p.m. PST.

940 Columbia Avenue, Ri verside, CA 92507

877.888.9004 • Fax 951.787.8747 • proficientaudi o.com

Audio Sections

Rated Power/Channel 30 Watts, 20Hz - 20kHz

(RMS, 2 channels driven into 8 Ω)

THD (at rated power) < 0.7%

Power/Channel 45 Watts @ 1kHz

(RMS, 2 channels driven into 4 Ω)

Input Sensitivity 300 mV

(For rated power @ max VC)

Input Impedance (source inputs) > 22 kΩ

Input Overload (source inputs) 2.5 V

Output Voltage @ Pre-Outs 1.7 V, VC Setting, VC Max

(w/300 mV @ source inputs) 810 mV, NVC Setting

Output Impedance (pre-outs) < 300 Ω

Frequency Response (@ 1 watt @ 8 Ω) 20Hz - 20kHz ± 1.5dB

Channel Separation > 50dB @ 10kHz

Crosstalk Between Sources > 65dB @ 10kHz

S/N Ratio (re: rated output, > 95dB (VC 20dB IEC A ,

source inputs shorted) below FCW)

Bass Control Range ±10dB @ 100Hz

Treble Control Range ±10dB @ 10kHz

Control Sections

Contact Closures (dry) 2A, 30V AC/DC Max

Phone Page In Audio Line Level, > 22 kΩ

– Voltage/Impedance

Doorbell/Status In 1 & 2, 10 mA @ 12V AC/DC

3V - 30V AC or DC

Common IR Out

– HI (high power) 9 V Active High, 82 Ω (110 mA Peak)

– LO (emitter power) 9 V Active High, 670 Ω (13 mA Peak)

Zone IR Outs 9.2 V Active High, 620 Ω (13 mA Peak)

– Voltage/Impedance

Source IR Outs (and loop) 11.5 V Active High, 390 Ω (29 mA Peak)

– Voltage/Impedance

Common Status Out 9.5 V @ 100 mA

(0-12V DC)

General

power Consumption

No Signal (idle) 50 Watts

At 1/8 Rated Power 110 Watts

(3.75 watts/channel)

Line Ratings (120V AC version) 120V AC, 1.8A

Rear Panel Fuse (120V AC version) T5AL 250V

Line Ratings (230V AC versions) 230V AC, 0.9A

Rear Panel Fuse (230V AC versions) T2. 5AL 250V

Dimensions (H x W x D) 513⁄16" x 171⁄8" x 151⁄2"

148mm x 435mm x 394mm

Weight 20 lbs (9.1 kg)

Limited Two-Year Warranty

Proficient Audio Systems warrants to the o riginal retail p urchaser only tha t this product w ill

be free from defec ts in materials an d workmanship fo r a period of t wo years, provid ed the

speaker was purchased f rom a Proficient Audio Systems Author ized Dealer.

Defective products must be shippe d, prepaid and insured, together with proof of purchase,

to the Proficient Audio Systems Authorized Dealer from w hom they were purchased, or to

Proficient Audio Systems at the address listed on this inst allation instruction manual. Freight

collect shipments will be refused. It is p referable to ship this product in th e original shipping

container to lessen the chance of transit damage. In any case, the risk of loss or damage in transit

is to be borne by the purchaser.

If, upon examination at the Factory or Pr oficient Audio Sys tems Authorized D ealer, it is

determined that the uni t was defective in materials or wor kmanship at any tim e during this

warranty period, Pro ficient Audio Sys tems or the Profi cient Audio Systems A uthorized Deale r

will, at its option, re pair or replace t his product at n o additional char ge, except as set f orth

below. If this model is no longer availab le and can not b e repaired eff ectively, Profic ient Audio

Systems, at its sole opt ion, may replace th e unit with a curr ent model of equ al or greater valu e.

In some cases where a n ew model is subs tituted, a modif ication to the m ounting surface may

be required. If mount ing surface mo dification is r equired, Profi cient Audio Systems as sumes

no responsibility or liability for s uch modificati on. All replaced parts and pro duct become th e

property of Prof icient Audio Systems . Products rep laced or repaire d under this Warran ty will

be returned to the ori ginal retail pur chaser, within a reaso nable time, frei ght prepaid.

This Warranty does not include ser vice or parts to repair damage caused by accident, dis aster,

misuse, abuse, negligence, inadequate pa cking or shipping procedu res, commercial use, volt-

age inputs in excess of the rated maxim um of the unit, or servi ce, repair or modificati on of the

product which has not been author ized or approved by Profici ent Audio Systems. This Warranty

also excludes normal cosmetic deterior ation caused by environmenta l conditions. This warrant y

will be void if the Serial Number on the product has been re moved, tampered with or de faced.

This Warranty is in lieu of all other expressed war ranties. If the product is defe ctive in materials

or workmanship as warranted above, the purchaser’s sole re medy shall be repair or replaceme nt

as provided above. In no event will Proficient Audio Systems be liable for any incidental or con-

sequential damages arising out of the use or inabilit y to use the product, even if Profic ient Audio

Systems, or a Proficient Audio Systems Authorized Dealer has been advised of the possibilit y of

such damages, or for any claim by any other party. Some s tates do not allow the exclusion or

limitation of consequential damages, so the above limit ation and exclusion may not apply.

All implied warranties on the product are limited to the duration of this e xpressed Warrant y.

Some states do not allo w limitation on th e length of an im plied warranty. I f the original re tail

purchaser resides in suc h a state, this lim itation does not apply.

ZonE STATUS LEDS

LED indicators and labels:

Four blue LEDs indicate

that one or more zones

are currently active.

MASTER poWER SWITCh

When pressed in, the M4

permits zones to be turned

ON and OFF by keypad or

touch panel commands.

BLUE InDICAToR LIGhT

Blue indicates the master

power switch is ON and one

or more zones are active.

Red is OFF.

Keypad RJ45 T568B Standard T568A Standard

12V Pin 2, 7 Orange, White/Brown Green, White/Brown

DATA/IR Pin 4, 5 Blue, White/Blue Blue, White/Blue

GND Pin 1, 8 White/Orange, Brown White/Green, Brown

485A Pin 3 White/Green White/Orange

485B Pin 6 Green Orange

1 2 3 4 5 6 7 8

T568A Standard

1 2 3 4 5 6 7 8

T568B Standard

SPKRS

LR+

+ – –

ZONE 4

L R PRE-OUT

NVC

KEYPAD

IR OUT

PMKIR

Master Keypad

with IR Receiver

ADDRESS

KEYPAD EXPANSION

Riverside, CA. USA • Made in China

proficientaudio.com

+ RELAY

– RELAY

+12V

DATA

GND

485 A

485 B

Keypad

Connector

Rear View

CAUTION:

Colors shown are based on T568B RJ45 termination.

SEE CHART BELOW

for T568A and T568B

wiring termination.

Inter-Room

Twisted Pair

CAT5 Cable

1,000' (305m) Max.

Orange

White/Brown

Blue

White/Blue

Brown

White/Orange

White/Green

Use Twisted Pair

for 485A & 485B

Green

figure 11 Ribbon Cable – PMKIR Right

figure 12 Ribbon Cable – PMKIR Left

KEYpAD hooKUp

noTE: The numeric and function keypads will not

work on their own. They must be connected to a

master keypad using the 3-connector ribbon cable

supplied (included with each model). The cable is

symmetrical so it can be connected with the red

striped side up or down, to best fit the configuration.

figure 11 shows it connected so that the PMKIR

master keypad will be to the right of the PNK numeric

and PFK function keypads when mounted, whereas

figure 12 places the PMKIR to the left.

figure 13 RJA-1.1 Adapter

figure 14 RJA-1.1 Attached to Keypad and CAT5

figure 15

Using CAT5 Cable to Connect PMKIR Keypads to M4

figure 10 Moving and Placing Buttons

figure 9 Remove Decorator Insert Panel

1. The keypads have a pre-installed set of buttons in

place. These may not match the source and function

arrangements you need or desire. To change them,

release the tabs on each end of the keypad, figure 8,

and remove the decorator insert panel, exposing the

key buttons, figure 9.

2. Starting with the Zone 1 PMKIR (master keypad),

and using the extra buttons supplied, if needed,

move and place the source and function buttons in

the arrangement you want. See figure 10. When you

finish the arrangement, replace the decorator insert

panel over the buttons, being careful to see that the

buttons align correctly with the panel openings.

Press the panel down until the tabs “snap” into place.

3. Repeat these steps for each of the other zone

master keypads. Each zone can have its own unique

configuration… but, it is best to keep them as similar

as possible to simplify programming and operation.

4. In the same way, configure the buttons on the

numeric and function keypads (not included) that

you may chose to use in some zones.

5. Connect all keypads to their assigned zones on

the M4 as shown in figure 7. Be sure to strip then

connect the various colored CAT5 leads to the correct

terminals on each keypad end. Refer to figure 15.

ConfIGURE ThE KEYpAD BUTTonS

noTE 1: If you want to use RJ45 connectors for

connecting the CAT5 cable to the keypads, you can do

so by using the Proficient model RJA-1.1 RJ45-to-Wire Pin

Adapters. See figure 13 and figure 14. Simply insert the

RJA-1.1 pins into the keypad’s connection terminals and

snap the levers in place. Be sure to orient them correctly

as shown.

figure 8 Release Tab

1301-72400 (rev1)

figure 1

M4 Front Panel Features

RS232

PHONE (PAGE IN) DOORBELL / STATUS IN

CONTROL

PORT

FIRMWARE

UPGRADE

OFF ON

COMMON

IR OUT

LO HI

STATUS OUT: 0 to +12V

120V 60Hz 1.8A ~

FUSE: T5AL 250V

DATA I/O

CONTACT CLOSURE

EXPANSION PORTS

COMMON

SOURCE 1

LOOP

OUT

LOOP

L R

INPUTS

SOURCE 2

LOOP

OUT

LOOP

L R

INPUTS

SOURCE 3

LOOP

OUT

LOOP

L R

INPUTS

SOURCE 4

LOOP

OUT

LOOP

L R

INPUTS

SOURCE 5

LOOP

OUT

LOOP

L R

INPUTS

SOURCE 6

LOOP

OUT

LOOP

L R

INPUTS

SPKRS

LR+

+ – –

ZONE 4

L R PRE-OUT

NVC

KEYPAD

IR OUT

Riverside, CA. USA

Made in Taiwan

SPKRS

LR+

+ – –

ZONE 3

L R PRE-OUT

NVC

KEYPAD

IR OUT

SPKRS

LR+

+ – –

ZONE 2

L R PRE-OUT

NVC

KEYPAD

IR OUT

SPKRS

LR+

+ – –

ZONE 1

L R PRE-OUT

NVC

KEYPAD

IR OUT

M4 fEATURES

M4 Multi-Zone Audio Amplifier/Controller

The M4 is a four-zone, six-source Audio Amplifier/Controller. It serves as the

“brains” of the entire keypad system. The M4 provides audio switching for

six sources and 30W/channel audio power amplifiers for four zones. It also

has connection termination facilities for the controlled whole house system.

DooRBELL/STATUS In 1 & 2 JACKS

These 3.5mm mini phone trigger inputs work in

conjunction with the PHONE PAGE IN jack. When

triggered, the phone inputs can be turned on as

programmed by proficient Editor. If audio paging is

not required, these 1 & 2 jacks may also be pogrammed

as STATUS inputs for power management of source or

zone components. They accept input levels of 3V to 30V

AC or DC for the trigger ON condition. The voltage level

must drop below 1V AC or DC for the OFF condition.

IR oUT

This 3.5mm mini jack, one for each zone, provides dedicated Zone IR

output initiated from the respective zone inputs. They may control

specific zone components when you want to prevent the control of it

from the other zones.

EXpAnSIon poRTS

RJ45 jacks provide for connection

of specialized RS485 controlled

products and for looping to

additional M4 controllers for zone

expansion capability.

RS-232 DATA I/o

Communication port.

phonE pAGE In JACK

This jack provides input porting for audio feeds from

door mikes or other forms of phone or doorbell

paging. The jack is programmable by proficient

Editor, to turn on as events, when triggered by the

DOORBELL/STATUS IN Jack.

ConTACT CLoSURE

Provides a single pole dry relay

contact to activate any device that

can be controlled or triggered by a

switch closure. The closure can be

programmed within proficient Editor

to be activated by keypad presses,

Command Library IR, or within macros

for Momentary, Toggle and Open/

Close Paired operations. Spring-loaded

terminals accept wire sizes from 28 to 14

AWG. Internal relay contacts are rated at

2A/30V AC or DC.

ConTRoL poRT & fIRMWARE UpGRADE SWITCh

3.5mm 4-circuit mini phone jack allows several control functions. All keypad

programming is accomplished via this port using proficient Editor in conjunction

with the mating Transfer Cable. It also accommodates factory firmware updates

in conjunction with the fIRMWARE UpGRADE off/on Switch. Be sure to leave

this switch in the off position at all times, except, as instructed within proficient

Editor, when you are doing a firmware update. Such updates ensure that you can

always have the latest functionality improvements in the field. Another function of

this port is that you can control installed system components with bi-directional

data via touch panels or computers using RS232 protocol.

CoMMon IR oUTpUT & hI/Lo SWITCh

3.5mm mini phone jack provides a common IR output derived from all of

the zone IR inputs and from keypad initiated IR commands derived from

the internal IR library. High or low IR power output is set by means of the

hI/Lo switch. Set it to the Lo setting when driving standard low power

emitters (i.e, Proficient IR single flasher). Set it to the hI position when

driving a high power emitter (i.e, a blaster) for teaching IR commands into

learning remotes. Caution: The hI position will damage or destroy low

power emitters!

CoMMon STATUS oUT poRT

This 3.5mm mini phone jack will go high (+12V DC)

when any zone is turned ON and will go LOW (under 1V

DC) when the last zone is turned OFF. The max. output

of this jack is 100 mA at 9.5V DC.

IR oUT JACKS

These 3.5mm mini phone jacks, one for each source, provide

dedicated IR output to specific source components. When a

source is selected on a keypad, IR function commands are

routed directly to that source. This prevents cross-control

interference between two or more sources that have

identical IR commands.

IR Loop JACKS

These six 3.5mm mini phone jacks, one for each source, are

provided exclusively for zone expansion capability when

using two or more M4 controllers. They permit the

source IR signals from the added zones to be carried to

the source component emitters.

L & R AUDIo In & Loop JACKS

These RCA jacks – four for each source – provide audio

signal inputs and buffered loop outputs, for each

source. The buffered outputs can be used to drive local

components or loop the signals to the additional zone

inputs of other M4 controllers when using them for source

expansion.

IEC TYpE AC

Mains receptacle and fuse mates with included AC

power cord. Also houses the rear panel replaceable AC

mains fuse (T5AL 250V for 120V, and T2.5AL 250V for

230V/240V)

L & R pRE-oUT JACKS

These RCA jacks provide line level

audio outputs for driving external

power amplifiers for additional rooms

within zones, where needed.

VC-nVC SWITCh

The audio output from the PRE-OUT jacks can

either be controlled by the internal volume

control of the M4 (VC position) or be a fixed

line level output in the no volume control

(nVC position). In either case, the tone control

remains available for room “EQ” settings.

KEYpAD ZonE InpUTS

These RJ45 terminals allow for easy

connection of the inter-room wiring

from keypads in the various rooms.

Normally this is accomplished using

CAT5 cable with home-run lengths of

up to 1000'.

L & R SpEAKERS TERMInALS

These 4-circuit plugable screw-down

terminals accept wire sizes from 14 to

28 AWG. They allow quick connection of

the internal amplifiers to stereo pairs of

speakers in the various zone rooms.

figure 2

M4 Rear Panel Features