PART | R0402A |
To locate the parts listed below, refer to the EXPLODED DRAWING attached in the center of this manual.
Key |
|
| Key |
|
| Key |
|
|
No. | Qty. | Description | No. | Qty. | Description | No. | Qty. | Description |
1 | 1 | Motor Belt | 46 | 14 | Isolator Screw | 92 | 1 | Left Foot Grip |
2 | 1 | Pulley/Flywheel/Fan | 47 | 15 | Plastic Fastener | 93 | 1 | Motor Tension Bushing |
3 | 4 | Motor Nut | 48 | 1 | Foam Grip (Right) | 94 | 1 | Motor Hood |
4* | 1 | Motor/Pulley/ | 49 | 2 | Belt Guide | 95 | 2 | Front Wheel |
|
| Flywheel/Fan | 50 | 1 | Book Holder | 96 | 1 | Incline Motor Shield |
5 | 1 | Incline Motor Bolt | 51 | 1 | Front Belly Pan | 97 | 4 | Thick Base Pad |
6 | 1 | Rear Pad (Left) | 52 | 1 | Power Supply | 98 | 1 | 12” Audio Wire |
7 | 1 | Incline Motor | 53 | 4 | Cable Tie Clamp | 99 | 1 | Upright Grommet |
8 | 2 | Incline Motor Spacer | 54 | 4 | Cable Tie | 100 | 1 | Allen Wrench |
9* | 1 | Latch Assembly | 55 | 1 | Walking Belt | 101 | 21 | Screw |
10 | 1 | Small Plate | 56 | 1 | Latch Spacer | 102 | 1 | Audio Wire Nut |
11 | 1 | Rear Foot Spacer | 57 | 1 | Rear Roller | 103 | 2 | Extension Leg |
12 | 1 | Frame | 58 | 1 | Belly Pan Spacer | 104 | 2 | Base Endcap |
13 | 1 | Hand Pulse Wire | 59 | 2 | Rear Foot | 105 | 1 | Shock |
14 | 1 | Incline Motor Pivot Bolt | 60 | 6 | Rear Foot Screw/ | 106 | 1 | Choke |
15 | 8 | Incline Motor Nut |
|
| Hood Screw | 107 | 2 | Pulse Bar Bolt |
16 | 4 | Belt Guide Screw | 61 | 1 | Ground Wire | 108 | 2 | Pulse Bar Washer |
17 | 4 | Plastic | 62 | 5 | Ground Wire Screw | 109 | 1 | Pulse Bar |
18 | 2 | Hood Bracket (short) | 63 | 1 | Belly Pan | 110 | 1 | Foam Grip (Left) |
19 | 1 | Hood Bracket (long) | 64 | 1 | Rear Endcap | 111 | 1 | Trim Guard |
20 | 2 | Warning Decal | 65 | 2 | Rear Roller Adj. Bolt | 112 | 1 | Shield |
21 | 1 | Reed Switch | 66 | 1 | Motor | 113 | 2 | Static Decal |
22 | 1 | Reed Switch Clip | 67 | 1 | Latch Decal | 114* | 2 | Extension Leg |
23 | 1 | Motor/Controller Wire | 68 | 6 | Platform Screw |
|
| Assembly |
24 | 1 | Controller | 69 | 1 | Incline Motor Plate | 115 | 2 | Incline Pivot Nut |
25 | 1 | Electronics Bracket | 70 | 1 | Catch | 116 | 1 | Console Base Bottom |
26 | 1 | Circuit Breaker | 71 | 1 | Walking Platform | 117 | 2 | Upright Endcap |
27 | 1 | Power Cord | 72 | 5 | 8” Cable Tie | 118 | 1 | Right Foot Grip |
28 | 1 | Power Cord Grommet | 73 | 1 | Jack | 119 | 2 | Base Pad |
29 | 1 | On/Off Switch | 74 | 1 | Motor Tension Bolt | 120 | 2 | Rear Isolator |
30 | 18 | Hood Bracket Screw/ | 75 | 2 | Interface Bracket | 121 | 1 | Frame Guide |
|
| Incline Shield Screw | 76 | 15 | Small Screw | 122 | 2 | Frame Guide Screw |
31 | 1 | Incline Base | 77 | 1 | Console | # | 1 | 14” Blue Wire, 2F |
32 | 2 | Frame Pivot Bolt | 78 | 2 | Ground/Switch Washer | # | 1 | 4” Blue Wire, 2F |
33 | 2 | Frame Pivot Spacer | 79 | 4 | Long Screw | # | 1 | 4” Black Wire, 2F |
34 | 1 | Upright Wire Harness | 80 | 1 | iFIT.com Wire | # | 1 | 12” Green Wire, F/R |
35 | 1 | Front Roller Adj. Bolt | 81 | 4 | Motor Star Washer | # | 1 | 8” Green Wire, 2 Ring |
36 | 2 | Roller Adj. Washer | 82 | 1 | Upright | # | 1 | 14” White Wire, M/F |
37 | 2 | Motor Tension Nut | 83 | 2 | Incline Base Pivot Bolt | # | 1 | 8” White Wire, M/F |
38 | 4 | Motor Bolt | 84 | 1 | Rear Pad (Left) | # | 1 | 4” Red Wire, M/F |
39 | 1 | Optic Switch | 85 | 2 | Handrail Extension | # | 1 | 20” Wire Harness |
40 | 1 | Optic Switch Nut | 86 | 2 | Wheel Bolt | # | 1 | User's Manual |
41 | 1 | Optic Switch Bolt | 87 | 1 | Console Base |
|
|
|
42 | 1 | Front Roller/Pulley | 88 | 1 | Motor Tension Washer | # These parts are not illustrated | ||
43 | 1 | Magnet | 89 | 1 | Incline Stop Bracket | * Includes all parts shown in the | ||
44 | 2 | Platform Screw (mid) | 90 | 1 | Key/Clip | box |
|
|
45 | 4 | Isolator | 91 | 1 | Optic Disk |
|
|
|
27
