28. Press two 50mm Square Inner Caps (22) into the | 28 |
|
|
|
Butterfly Frame (42). |
| 110 |
| |
|
|
| ||
Attach the Butterfly Frame (42) to the Rear Top |
|
| 99 |
|
Frame (39) with two M10 x 78mm Bolts (110), two |
|
| 99 |
|
M10 Washers (99), and two M10 Nylon Locknuts |
|
| 39 |
|
(97). Do not tighten the Locknuts yet. |
|
|
|
|
Attach the Butterfly Frame (42) to the Center |
|
|
| 37 |
|
| 97 |
| |
Upright (37) with two M10 x 68mm Bolts (113), |
|
|
| |
|
|
|
| |
two M10 Washers (99), and two M10 Nylon |
| 97 |
|
|
Locknuts (97). Do not tighten the Locknuts yet. |
|
|
| |
Tighten all of the M10 Nylon Locknuts (97) | 22 |
|
|
|
used in steps |
|
| 42 |
|
Screws (119) used in step 22 and the 1/4” x |
|
|
| |
|
|
|
| |
9.5mm Allen Head Set Screws (120) used in |
|
|
|
|
step 23. |
|
|
|
|
| 113 | 99 | 22 |
|
|
|
| ||
|
|
|
| |
29. Lubricate both axles on the Butterfly Frame (42) | 29 |
|
|
|
with grease. |
|
|
| |
|
|
|
| |
Press two 50mm Square Inner Caps (22) into the | Lubricate Axle |
|
| |
ends of the Right Fly Arm (43). Insert a Fly Arm | 92 |
|
|
|
Bushing (92) into the Arm. Wet the end of the |
|
|
| |
|
| 42 |
| |
Arm with soapy water and slide a Fly Foam Pad |
|
|
| |
(95) onto it. | 43 |
| Bracket |
|
|
|
|
| |
Have another person slide the Right Fly Arm (43) | 93 |
| 22 | 44 |
onto the right axle on the Butterfly Frame (42). |
| |||
|
|
|
| |
Note: Be careful not to confuse the Left Fly |
| 94 |
|
|
Arm (44) with the Right Fly Arm. Make sure |
|
|
| |
|
|
|
| |
that the upper end of the Arm is behind the |
|
|
|
|
indicated bracket on the Butterfly Frame. | 22 |
|
|
|
|
|
|
| |
Tap two 25mm Retainer Rings (93) onto the axle of | 95 |
|
|
|
the Butterfly Frame (42) with the included retainer |
| Axle |
| |
tool. Make sure that the teeth on the Retainer |
|
|
| |
|
| 42 |
| |
Rings bend toward the tool, as shown in the |
|
|
| |
|
|
|
| |
inset drawing. Tap the 25mm Round Outer Cap |
|
| 93 |
|
(94) onto the right axle on the Butterfly Frame. |
|
|
| |
|
|
|
| |
Attach the Left Fly Arm (44) in the same |
|
| Retainer |
|
manner. |
|
|
| |
|
| Tool |
| |
|
|
|
| |
30. During cable assembly, refer to the CABLE | 30 |
|
|
|
DIAGRAMS on page 22 for cable identification |
|
|
| |
|
|
|
| |
and to verify cable routing. |
|
|
|
|
Locate the Butterfly Cable (83). Attach the |
|
| 129 |
|
Cable to the Left Fly Arm (44) with an M8 x |
|
|
|
|
16mm Shoulder Bolt (129) and an M8 Nylon |
|
| 83 |
|
Locknut (96). |
|
|
|
|
|
|
| 96 |
|
|
| 44 |
| |
| 14 |
|
|
|
