MAINTENANCE AND STORAGE
1. Loosen the Lock Knob (68) on the right side of the |
Frame (1). Slide the Seat Frame (3) out until it |
stops. Tighten the Lock Knob. |
1 | 68 |
| 3 |
| 1 |
Inspect and tighten all parts of the exercise cycle reg- ularly. The exercise cycle can be cleaned with a soft, damp cloth. To prevent damage to the console, keep liquids away and keep the console out of direct sun- light.
BATTERY REPLACEMENT
If the console does not function properly, the batteries should be replaced. To replace the batteries, refer to assembly step 12 on page 7.
CRANK ADJUSTMENT
dard screwdriver in one of the slots in the slotted bearing nut. Lightly tap the screwdriver with a ham- mer to turn the slotted bearing nut counterclockwise until the arms are no longer loose. Do not overtight- en the slotted bearing nut. When the slotted bearing nut is properly tightened, tighten the crank cut.
HOW TO STORE THE EXERCISE CYCLE
When the exer- |
| |
cise cycle is not | 1 | |
in use, it can be | ||
68 | ||
folded for com- |
| |
pact storage. |
|
Identify the Rear Stabilizer (76), which has no |
wheels. Attach the Rear Stabilizer to the Seat Frame |
(3) with two M10 x 58mm Carriage Bolts (74) and |
two M10 Nylon Locknuts (72). |
2. Identify the Front Stabilizer (75), which has wheels. |
Attach the Front Stabilizer (75) to the Frame (1) with |
72 |
72 |
76 |
74 |
2 |
If the arms of the Crank (29) become loose, they should be tightened in order to prevent excessive wear. Loosen the crank nut on the
Crank Nut
Slotted
Bearing
Nut
Refer to the |
|
drawing at the |
|
right. Loosen the |
|
Lock Knob (68) | 3 |
on the right side |
|
of the Frame (1). |
|
Slide the Seat |
|
Frame (3) as far |
|
into the Frame |
|
two M10 x 58mm Carriage Bolts (74) and two M10 |
Nylon Locknuts (72). |
72 |
1 |
Wheels |
left arm of the Crank. Place the end of a stan-
29
as it will go. Tighten the Lock Knob. Store the exer- cise cycle indoors, away from moisture and dust.
3.Attach the Upright (2) to the Frame (1) with three M10 x 25mm Button Head Screws (25) and three M10 Split Washers (26). Be careful not to pinch the Reed Switch Wire (13) or the Resistance Cable (10).
4.Route both Adapters (73) up through the Upright (2) as shown.
Attach the Handlebar (4) to the Upright (2) with two M6 x 25mm Hex Head Screws (14) and two M6 Split Washers (67), but do not tighten the Screws yet.
Make sure that the Screws are threaded into the indicated holes. Note: Two additional Screws will be attached in step 6.
|
| 75 |
|
| 74 |
3 |
|
|
2 |
|
|
|
| 25 |
26 |
| 26 |
|
| 25 |
25 | 10 | 13 |
| ||
|
| |
|
| 1 |
4 |
| 14 |
|
| |
67 |
| 67 |
| 73 | |
|
| |
14 |
| 4 |
2 |
|
|
12
5
