2. | Attach a Wheel (66) to the base of the Uprights (69) with | 2 |
| 64 |
|
| a Wheel Bolt (64) and a Nut (13) as shown. Do not |
|
| ||
| overtighten the Nut; the Wheel should turn freely. |
| 69 |
| 66 |
| With the help of a second person, carefully tip the tread- |
|
| ||
| mill onto its other side. See assembly step 1, and attach |
|
|
|
|
| the other Extension Leg (63) and the remaining two |
|
|
|
|
| Base Pads (57). Then, attach the other Wheel (66) as |
|
|
| 13 |
| described above. |
|
|
| |
| With the help of a second person, carefully tip the tread- |
|
|
|
|
| mill down so the Uprights (69) are in a vertical position. |
|
|
|
|
3. | Insert the tab on one of the Handrail Brackets (21) into the | 69 | |
| slot in the right Upright (69). Attach the Handrail Bracket | 3 | |
| with a 3/4” Screw (2) and a Small Star Washer (24). |
| Slot |
| Attach the other Handrail Bracket to the left Upright |
| |
| (not shown) in the same way. |
| 21 |
|
|
|
|
| 224 |
|
|
|
|
4. If there is a board between the Uprights (69), remove the | 4 |
|
|
|
|
|
two bolts attaching the board. Discard the board and the |
|
| 71 |
|
| |
bolts. | 37 |
|
|
|
| |
Identify the Right Handrail (72), which has a large hole in | 95 |
|
|
|
|
|
the left side. Cut the plastic tie securing the Upright Wire |
|
|
| 42 | Hole | |
(42) to the right Upright (69). Feed the Upright Wire into |
|
|
| 37 | ||
the hole in the bottom of the Right Handrail and out of |
|
| 69 |
|
| |
the large hole in the side. Note: It may be helpful to use |
|
| 95 |
|
| |
needlenose pliers to pull the Upright Wire out of the hole. |
|
|
|
|
| |
Press a Handrail Cap (16) onto the lower end of the |
|
|
| 72 |
|
|
Right Handrail (72) as shown. Set the Right Handrail on |
|
|
|
|
|
|
the right Upright (69) while sliding the lower end of the | 24 |
|
|
|
| 69 |
Right Handrail onto the right Handrail Bracket (21). |
|
|
|
| ||
Finger tighten a Handrail Bolt (37) with a Handrail Star |
|
|
|
|
|
|
Washer (95) into the Right Handrail and the right |
| 16 |
|
|
|
|
Upright. Next, attach the lower end of the Right Handrail |
|
|
| 16 |
| |
with a 3/4” Tek Screw (58) and a Small Star Washer | 58 |
|
|
|
| |
(24). Then, tighten the Handrail Bolt. |
|
| 24 |
|
| |
Attach the Left Handrail (71) in the same way. Note: |
|
|
|
| 21 | |
There is not an upright wire on the left side. |
|
|
| 58 |
| |
|
|
|
|
|
|
7