PYLE Audio PICL82 Connecting The Unit To Power, Connecting The Loudspeakers, Setting The Time

LOCATION OF CONTROLS

1.	Speakers	16.	CD Door Open Button
2.	Power/Alarm Off Button	17.	CD Door
3.	Play/Pause/Sync Button	18.	Display
4.	Function/Clock Adj. Button	19.	Remote Sensor
5.	Skip-/Tune- Button	20.	Adjustable Dock Dial
6.	Skip+/Tune+ Button	21.	iPod/iPhone Connector
7.	Memory-/Alarm 1 Button	22.	FM Wire Antenna
8.	Memory+/Alarm 2 Button	23.	Aux-In Jack
9.	P-Mode Button	24.	DC In Jack
10.	Sleep Button	25.	Remote Control

11.Snooze Button

12.Stop Button

13.Program/Mem Button

14.Volume– Button

15.Volume+ Button

CONNECTING THE UNIT TO POWER

Plug one end of the AC/DC adaptor into the DC-In jack, and then plug the other end into AC wall outlet. Before switching on the unit, make sure that the voltage of your electricity supply is the same as that indicated on the rating plate.

CONNECTING THE LOUDSPEAKERS

Connect the cables of the two loudspeakers to the corresponding input (R) for the right speaker and input (L) for the left speaker, located at the side of the unit.

Warning: Connect the loudspeakers before powering the unit. The unit may not work properly or get damaged if you use speakers different than the ones supplied with the unit.

SETTING THE TIME

Before starting to set the time, make sure that the unit is in POWER OFF Mode.

If you have iPod (Except iPod Shuffle) or iPhone

1.Dock in the iPod/iPhone on the 30 pins Connector

2.Press the ‘PLAY/PAUSE/SYNC’ button for a few seconds until the display will show SYNC with flashing, then the unit will synchronize the time same as the iPod/iPhone’s automatically.

If you do not have any iPod/iPhone units

1.Press and hold the ‘FUNC/CL ADJ’ button for a few seconds, the hour digit in the display will start flashing.

2.Press the ‘SKIP+/TUNE+’ or ‘SKIP-/TUNE-‘ button to adjust the hour.

3.When the correct hour is selected, press the ‘FUNC/CL.ADJ’ button again, the minute digit in the display will start flashing.

4.Press the ‘SKIP+/TUNE+’ or ‘SKIP-/TUNE-‘ button to adjust the minute.

5.When the correct time is selected, press the ‘FUNC/CL ADJ’ button to store the time in the memory.

SETTING THE ALARM TIME

Before starting to set the alarm time, make sure that the unit is in POWER OFF mode.

1.Press the ‘MEM-/AL1’ or ‘MEM+/AL2’ button on the unit once (you can also use the ‘AL1’ or ‘AL2’ button on the remote control) and the AL1 or AL2 icon will appear in the display.

2.Press the ‘FUNC/CL. ADJ.’ button to select the alarm wake up source. The options are buzzer, iPod/iPhone, Radio or CD.

3.Press and hold the ‘MEM-/AL1’ or ‘MEM+/AL2’ button on the unit for a few seconds (you can also use the ‘AL1’ or ‘AL2’ button on the remote control), the alarm hour digit will begin flashing.

4.Press the ‘SKIP+/TUNE+’ or ‘SKIP-/TUNE-‘ button on the unit to adjust the alarm hour.

5.When the desired alarm hour is selected, press the ‘MEM-/AL1’ or ‘MEM+/AL2’ button again, (you can also use the ‘AL1’ or ‘AL2’ button on the remote control), the alarm minute digit will begin flashing.

6.Press the ‘SKIP+/TUNE+’ or ‘SKIP-/TUNE-‘ button on the unit to adjust the alarm minute.

7.When the desired alarm time is selected, press the ‘MEM-/AL1’ or ‘MEM+/AL2’ button again to confirm. (You can also use the ‘AL1’ or ‘AL2’ button on the remote control).

Note : If you choose iPod/iPhone or CD as the alarm wake up source, please make sure that you have the iPod/iPhone or CD in place.

- 4 - - 5 -