PYLE Audio PTA3000 manual Specifications, Rated Output Power, Stereo mode EIA both channels driven

SPECIFICATIONS

RATED OUTPUT POWER:

Stereo mode

(EIA both channels driven)

4 Ohms EIA, 1 kHz, 1% THD

8 Ohms EIA, 1 kHz, 1% THD Bridge mode, mono

8 Ohms EIA, 1 kHz, 1% THD

HUM & NOISE:

Stereo mode, below rated output power, 4 ohms

DISTORTION:

SMPTE-IM

INPUT SENSITIVITY & IMPEDANCE:

@rated output power, 4 ohms Balanced, TRS 1/4" phone jack Balanced, XLR (pin 2 positive)

Overall system gain per channel

DISTORTION: (THD, typical value)

Stereo mode, both channels driven, 4 Ohms 20 Hz to 20 kHz, 10dB below rated power 20 Hz to 2 kHz, at full rated power

300W RMS/chan	400W RMS/chan	500W RMS/chan	600W RMS/chan	700W RMS/chan	800W RMS/chan	900W RMS/chan	1000W RMS/chan
150W RMS/chan	200W RMS/chan	250W RMS/chan	300W RMS/chan	350W RMS/chan	400W RMS/chan	450W RMS/chan	550W RMS/chan
600W RMS	800W RMS	1000W RMS	1200W RMS	1400W RMS	1600W RMS	1800W RMS	2000W RMS
100dB, unweighted	100dB, unweighted	100dB, unweighted	100dB, unweighted	100dB, unweighted	100dB, unweighted	100dB, unweighted	100dB, unweighted
less than 0.01%	less than 0.01%	less than 0.01%	less than 0.01%	less than 0.01%	less than 0.01%	less than 0.01%	less than 0.01%
0.87V RMS (-1.2dBV)	1V RMS (0dBV)	1.12V RMS (+1dBV)	1.23VRMS(+1.79dBV) 1.32VRMS(+2.4dBV)		1.4V RMS (+2.9dBV)	1.5V RMS (+3.5dBV)	1.58V RMS (+3.97dBV)
10K Ohms per leg	10K Ohms per leg	10K Ohms per leg	10K Ohms per leg	10K Ohms per leg	10K Ohms per leg	10K Ohms per leg	10K Ohms per leg
10K Ohms per leg	10K Ohms per leg	10K Ohms per leg	10K Ohms per leg	10K Ohms per leg	10K Ohms per leg	10K Ohms per leg	10K Ohms per leg
40X(+32dB)	40X(+32dB)	40X(+32dB)	40X(+32dB)	40X(+32dB)	40X(+32dB)	40X(+32dB)	40X(+32dB)
less than 0.03%	less than 0.03%	less than 0.03%	less than 0.03%	less than 0.03%	less than 0.03%	less than 0.03%	less than 0.03%
less than 0.03%	less than 0.03%	less than 0.03%	less than 0.03%	less than 0.03%	less than 0.03%	less than 0.03%	less than 0.03%

FREQUENCY RESPONSE: Stereo mode, both channels driven +0, -1 dB @1 W RMS, 4 ohms +0, -3 dB @rated output, 4 ohms

DAMPING FACTOR: (Typical value) Stereo mode, both channels driven 8 Ohms, 1 kHz

20Hz to 20 kHz	20Hz to 20 kHz	20Hz to 20 kHz	20Hz to 20 kHz	20Hz to 20 kHz	20Hz to 20 kHz	20Hz to 20 kHz	20Hz to 20 kHz
5Hz to 50 kHz	5Hz to 50 kHz	5Hz to 50 kHz	5Hz to 50 kHz	5Hz to 50 kHz	5Hz to 50 kHz	5Hz to 50 kHz	5Hz to 50 kHz
Greater than 300	Greater than 300	Greater than 300	Greater than 300	Greater than 300	Greater than 300	Greater than 300	Greater than 300

FEATURE SET: ALL Models (++indicates each channel)

COOLING SYSTEM: Two-speed DC fan, air flow back to front

LOW CUT FILTER ++: -3dB @ 40 Hz, 12dB per octave

CROSSOVER ++: 150Hz, 4-pole Linkwitz-Riley approximation

INPUT++: Electronic balanced; Barrier Strip, XLR, TRS 1/4" (6.3mm)

CROSSOVER OUTPUTS ++: Low/Thru and High, TS 1/4" (6.3mm)

AMPLIFIER OUTPUTS: Speakons for Chan A, Chan B and Bridge; Binding, Posts

LED INDICATORS ++: Red, DDT/clipping; Green signal; Blue, power

AMP PROTECTION: Full short circuit, open circuit; over-temp thermal; RF; stable into any load

LOAD PROTECTION: Turn on/off muting, DC (triac crowbar), low-cut filter MAINS VOLTAGES AVAILABLE 100, 120, 230, 240 VAC, 50-60 Hz DIMENSIONS: Height: 3.5" (8.9cm), Width: 19" (48.3cm), Depth: 17.3" (44.1cm)

Specifications subject to change without notice