Presetting the Controls Before Use
Since sudden high output levels from your Pyle Pro mixer can damage not only audio devices connected to the mixer output but your hearing as well (especially if you are using headphones), please adjust the mixer’s controls BEFORE connecting AC power or turning on the unit.
Set up the mixer controls like this before you start:
| CONTROL | SETTING |
|
|
Power On/Off | OFF |
Balance | MID |
Gain | MID |
Tone Controls, Treble, Mid and Bass | 0 |
Connecting the Mixer Inputs
This mixer permits connection of up to five (5) audio input sources, including a microphone. Such a system might include, for example:
One Microphone | One Microphone | One Microphones | One Microphone |
Two Turntables | One Turntable | One Turntables | Two Turntables |
Two CD players | Two CD players | One CD player | One CD player |
| One Cassette Deck | One Cassette Decks | One Rhythm Synth |
|
| One VCR |
|
|
| ||
Please observe | Do not connect any audio source with a HIGH LEVEL OUTPUT to the LOW | ||
LEVEL PHONO 1 or PHONO 2 mixer audio input jacks (an audio source | |||
the following: | output with a volume control is HIGH LEVEL). | ||
|
|
|
|
MIC 1/2, CH 1/2/3, Master and Cue Levels | 0 |
Crossfader | CENTER |
Connecting the Outputs
After presetting the controls (above), you can then connect the mixer’s output jacks to the output devices’ input jacks. Before connecting these devices, however, be sure to preset their controls to
Connect audio inputs as follows:
1. DJ Microphone. Connect |
|
the DJ’s Microphone (not |
|
supplied) to the mic input jack. | DJ MIC |
The special combo jack on the |
|
| |
with either a 1/4” plug or XLR |
|
plug. |
|
Use 1/4” or
DJ MIC
avoid any damage to your equipment due to unexpected high output levels.
Set the output devices’ controls like this before you start:
| OUTPUT DEVICE | CONTROL | SETTING |
|
|
|
Tape Deck | POWER | OFF |
Amplifier/Receiver | POWER | OFF |
| TONE | FLAT |
Playing the Mixer’s Output Signal
To play the mixer’s output signal through your speaker system (for events such as parties, dances, conferences, etc.) connect an audio patch cord with
Recording the Mixer’s Output Signal
| Use 1/4” |
|
|
|
|
|
| jack |
|
|
|
|
|
2. High Level Output Audio |
|
|
|
|
|
|
Sources. Connect up to 4 |
|
|
|
|
|
|
such sources (tuner, cassette | Use RCA type |
|
|
|
| |
deck, CD Player, camcorder |
|
|
|
| ||
patch cables |
|
|
|
| ||
or VCR) to the input jacks for |
|
|
|
| ||
|
|
|
|
|
| |
Line 1 (if not being used as |
|
|
|
|
|
|
Phono 1 input), Line 2, Line |
|
|
|
|
|
|
3 (if not being used as Phono |
|
|
|
|
|
|
2 input), and Line 4. Please |
|
|
|
|
|
|
note that Phono 1 and Line 1 |
|
|
|
|
|
|
(as well as Phono 2 and Line |
|
|
|
|
|
|
3) use the same jacks. The |
|
|
|
|
|
|
|
|
|
|
|
| |
selector switch(e)s below the | High Level Output |
|
|
|
| |
|
|
|
| |||
jacks should be set to Line |
|
|
|
| ||
Audio Source |
|
|
|
|
| |
position if the jacks are used |
|
|
|
|
| |
LEFT output |
|
|
| NOTE! | ||
for the High Level input |
|
|
| |||
|
|
|
|
| ||
sources described here. |
|
|
|
|
|
|
RIGHT output | Be sure to place the input select switch(es) | |
in positions which reflect what the connected | ||
| ||
CD player, cassette deck, camcorder, VCR, etc. | input source is (Line in or Phono In)! | |
|
To record the mixer’s output signal, connect audio patch cords (not supplied) from the mixer’s REC (Record) L and R jacks to your tape deck’s left and right input jacks.
3.Turntables. Connect up to 2 turntables to the Phono 1 and Phono
2input jacks. Please note that Phone
1and Line 1 (as well as Phono 2 and Line 3) use the same jacks. The selector switch below the jacks should be set to Phono position if the jacks are used for phono inputs.
When using a turntable, you should also securely connect its ground wire (usually green or black) to the Ground screw on the input panel of the mixer.
Use RCA type patch cables
Magnetic cartridge turntable
LEFT output
RIGHT output
GROUND wire from turntable
2 – Pyle Pro Mixer Owner’s Manual | Pyle Pro Mixer Owner’s Manual – 3 |