QS434
FRONT PANEL
REAR PANEL
1 2 3
1 2 3 4 5
MENU
EXIT
6 7 8 9 0
4
OK
56
HDD REC ALM FULL NET
|
| 1 | 2 |
|
|
| AUDIO OUT | VIDEO IN |
|
|
|
| 1 | 3 |
- | + |
|
|
|
DC +19V |
| 2 | 4 | |
VIDEO OUT |
|
| ||
IN |
|
|
| |
3
AUDIO IN
13
24
VGA
RJ45 | +5V GND 485B 485A GND 1NO 1COM GND |
|
1 2 3 4
ALM IN
USB
7 | 8 | 9 |
4 5
6 | 7 | 8 |
9
Item # | Name/ Symbol | Description |
|
|
|
| |
1 | STANDBY | Press to set the system in standby mode. Press again to wake. | |
|
|
| |
2 | MENU/EXIT | Press to open/close the main menu. | |
|
|
| |
3 | CHANNEL/ | Press buttons | |
| NUMBERS | Press buttons | |
|
|
|
|
4 |
| ▲ | Press to move cursor up; in PTZ mode, press to pan |
|
| camera up. | |
|
| ▼ | Press to move cursor down; in PTZ mode, press to |
| NAVIGATION | pan camera down. | |
| ◄ | Press to move cursor left; in PTZ mode, press to pan | |
|
| ||
|
| camera left. | |
►Press to move cursor right; in PTZ mode, press to pan camera right.
5 | LED | Shows status of hard drive, recording, alarm, HDD full and | |
| INDICATORS | network. |
|
|
|
|
|
6 | IR SENSOR | IR Receiver for remote control. | |
|
|
|
|
7 |
| In menus, press to confirm selections; in PTZ mode, press to | |
| OK | change the navigation buttons to control a connected PTZ | |
|
| camera (not included) | |
|
|
|
|
8 |
| ◄◄ | Increase reverse playback speed 1X, 2X, 4X. |
|
| n/► | Press to freeze playback to one frame, then press |
| DURING | again to advance | |
| ► | Press to start playback | |
| PLAYBACK | ||
|
| ||
| PRESS: |
| |
| ►► | Press to slow playback speed by 1/2, 1/4, 1/8. | |
|
| ||
|
| ►► | Press to increase forward playback speed 1X, 2X, |
|
| 4X. | |
9 |
| USB | Connect a USB flash drive for data backup and |
|
|
| firmware upgrades |
|
|
|
|
Item # | Connector | Description | |
|
|
| |
1 | AUDIO | For connection to amplified speaker | |
OUTPUT | |||
|
| ||
|
|
| |
2 | VIDEO IN | Video input for connecting analog video signal input (BNC) | |
|
|
| |
3 | AUDIO IN | Audio input for connecting audio signal (4 feeds) | |
|
|
| |
4 |
| DC 19V Power Connection | |
|
|
| |
5 | VIDEO OUT | Video output for connecting TV (BNC) | |
|
|
| |
6 | NETWORK | For connecting Ethernet cable | |
|
|
| |
7 | VGA OUTPUT | To connect to VGA monitor | |
|
|
| |
| ALARM INPUT | 8 I/O Alarm input | |
|
|
| |
| ALARM | I/O Output for alarm | |
| OUTPUT | ||
|
| ||
|
|
| |
8 | RS485 | RS485 for connecting PTZ | |
|
|
| |
| RS232 | Debugging port | |
|
|
| |
| +12V | Power supply for DC relay, the current is 100MA (to prevent | |
| short circuits) | ||
|
| ||
|
|
| |
9 | USB | Mouse port | |
|
|
|
16 | 17 |
