![](/images/new-backgrounds/1198168/19816821x1.webp)
Specifications |
|
|
|
|
|
| |||||||||||
Frequency Response, ±3dB |
|
|
| ||||||||||||||
Frequency Range, |
|
|
| ||||||||||||||
Maximum Peak SPL | 129dB |
|
|
|
|
|
|
|
| 129dB | 129dB | ||||||
Nominal coverage, H x V | 60°x40° |
|
|
|
|
|
|
|
| 90°x40° | 120°x40° | ||||||
(as installed at factory) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Directivity Index | 12.8 |
|
|
|
|
|
| 11.3 |
| 9.6 | |||||||
Directivity Factor | 19.0 |
|
|
|
|
|
| 13.4 |
| 9.1 | |||||||
Acoustic Crossover Freq. | 1.32k Hz |
|
|
|
|
|
|
|
| 1.4k Hz | 1.2k Hz | ||||||
Transducer Description | LF: 15” (381mm) diameter, | 4” (102mm) voice coil, ferrite magnet |
| ||||||||||||||
| HF: 1.4” (36mm) exit diameter, 2.5” (64mm) voice coil, neodymium magnet, all models | ||||||||||||||||
Amp Power | LF: 800W, HF: 200W, all models |
| |||||||||||||||
Input Sensitivity | 1.2Vrms | (+4dB), all models |
|
|
|
|
|
|
| ||||||||
Input Headroom/Clipping | 7.5Vrms | (+19.5dB), all models |
| ||||||||||||||
Input Connector/Impedance | XLR female, 20k ohm, balanced, all models |
| |||||||||||||||
Output Connector | XLR male, wired in parallel with Input connector |
| |||||||||||||||
Controls, Indicators, and | Rotatable horn assembly, Gain control, 100 Hz | ||||||||||||||||
Adjustments | Power (blue LED), all models |
| |||||||||||||||
Protection, Agency certs. | Thermal limiting, On/Off muting, AC | ||||||||||||||||
AC Power Requirements |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
AC Power Connector | Factory supplied cordset: Neutrik Powercon on 10’ (3m) #18AWG 120V North American cordset | ||
Dimensions | 20.5” (521mm) W, 35.0” (889mm) H, 17.1” (432mm) D, including rear heatsink fins | ||
| Allow for 100mm (4.0”) of free space behind the enclosure to assure proper amplifier cooling | ||
Weight | 89 lb/41 kg | 88 lb/40 kg | 89 lb/41 kg |
Finish and Grill | All models- wear resistant textured paint finish with | ||
Notes: |
|
|
|
1- Maximum Peak SPL: Calculated by adding the loudspeaker’s sensitivity (1W at 1m) to the peak power (dBw) of the amplifier provided.
2- Coverage: Included angle between
3- Directivity Index (DI): Difference between
4- Directivity Factor (Q): Directivity index expressed as a power ratio Q=10 exp DI/10
5- Amplifier Power: The maximum sustained power at less than 1% clipping, averaged over the intended frequency range,
6- Input Sensitivity: The
to limiting. |
|
7- Input Headroom/Clipping: Maximum input voltage. |
|
8- Input Connector/Impedance: RF shunt capacitance should not reduce impedance by more than 30% at 20k Hz. | 11 |
9- TBD= to be determined, data not available at time of printing |