Using Auto Harmonize
•Auto harmonize does not work when you select full range chord auto accompaniment or no auto accompaniment.
•The harmony melody in auto harmonize mode uses Channel 5. You can change the tone or volume setting of the harmony by using the keyboard’s mixer function (see “Using the Mixer”).
Using the Mixer
•Normally, keyboard play is assigned to Channel 1. When you use auto accompaniment, parts are assigned to Channels
•When you use the keyboard as the sound source for another MIDI device, all 16 channels are assigned musical instrument parts, Channel 10 is reserved for drum parts only, per MIDI standard.
•The mixer settings also affect the corresponding MIDI output.
Using the Mixer
When using
The keyboard’s
The keyboard plays multiple parts at the same time in up to 16 separate channels during auto accompaniment, or memory playback, or when receiving MIDI data. You can control the on/off setting, volume, and parameters of each of the keyboard’s channels just as you would with a sound mixer.
This table shows the parts assigned to each channel.
&$$* | # |
|
|
|
|
1 | Main tone |
|
|
2 | Layered tone |
3 | Split tone |
|
|
4 | Layered/split tone |
5 | Harmonize tone |
|
|
6 | Auto accompaniment part 1 |
7 | Auto accompaniment part 2 |
|
|
8 | Auto accompaniment part 3 |
9 | Auto accompaniment bass part |
|
|
10 | Auto accompaniment rhythm part |
11 | Memory track 1 |
|
|
12 | Memory track 2 |
13 | Memory track 3 |
|
|
14 | Memory track 4 |
15 | Memory track 5 |
|
|
16 | Memory track 6 |
|
|
"#"$%#&##'()&$$*
You can turn a channel off to delete a specific part.
1.Press MIXER. The MIXER indicator and the last selected channel appear.
2.Repeatedly press + or – to select the channel you want to edit.
3.Repeatedly press (ENTER) then
(CURSOR) to display the current status of the channel — ' or .
4.Press + to turn on the channel or – to turn it off.
' (default): Turns on the current channel. A bar appears at the bottom of the level meter for the selected channel.
•tone
•tempo
•layer on/off
•effect type
•auto harmonize on/off
After selecting a rhythm, press PRESET. The keyboard enters synchro standby mode. Start the accompaniment. The rhythm plays at a suitable setting and the keyboard sounds the selected tone for the selected rhythm.
: Turns off the current channel. The bar at the bottom of the level meter disappears.
5.To edit other channels, press (EXIT) to return to the channel selection screen, then repeat steps
To exit the edit mode, press MIXER. The display shows the edited status of the channels.
"#"$%+#(
You can change the settings of six parame- ters for the selected channel.
1.Select the channel you want to edit as described in Steps 1 and 2 of “Editing the Status of a Channel”.
2.Press (ENTER) to enter the parameter edit mode.
3.Repeatedly press or to select the parameter you want to change.
Tone Parameters
'. (to *) — sets the tone assigned to the channel. When the assigned tone is an advanced tone, the display shows only two digits.
&0 ( to ) — controls the volume of the selected channel.
%' (()* to +),) — controls the pan
(relative position of the tone between left and right speaker channels). ()* is fully left, is the center position, and +), is fully right.
3 (Octave) $8 (( to +) – shifts the range of the tone up or down by octave.
Tuning Parameters
(Coarse) 0' (9* to +*) — coarsely tunes the pitch of the selected channel in semitone units.
'0' (9 to +) — fine tunes the pitch of the selected channel in cent
12
