installing batteries
mounting the phone
Trim Phone with Caller ID
Thank you for purchasing your Trim Phone with Caller ID from RadioShack.
MUTE - Hold down to talk without the caller hearing your
conversation.
FLASH - If you have Call Waiting, press FLASH to answer an incoming call without disconnecting the current call. Press again to return to the first call.
REDIAL/PAUSE
-Press to dial the last phone number you entered.
Your phone requires three AA batteries (not supplied) for power.
1.Use a
2.Insert three AA batteries, matching the polarity symbols (+ and
3.Snap the battery compartment door back into place. When the low battery icon appears on the display or the display dims, replace the batteries.
Battery Notes:
• Dispose of old batteries promptly and properly. |
• Do not burn or bury batteries. |
• Use only fresh batteries of the required size and |
recommended type. |
• Do not mix old and new batteries, different types |
of batteries (standard, alkaline, or rechargeable), or |
rechargeable batteries of different capacities. |
• If you do not plan to use the phone for two weeks |
or longer, remove the batteries. Batteries can leak |
chemicals that can destroy electronic parts. |
selecting a location
Select a location for your telephone that is:
•Near a telephone jack
•Not in the way of normal activities
mounting the phone
You can mount your telephone on a wall plate, on a wall, or place it on a shelf, desk, or table.
on a wall plate
1.Plug one end of the supplied short modular cord into the modular jack on the back of your phone.
2.Route the cord through the groove on the bottom of the base. Secure the cord with the tabs.
3.Plug the other end of the cord into a wall plate with a modular phone jack.
on a wall
1.Drill two holes 3 1/4 inches (82.5 mm) apart, one below the other.
2.Thread two screws (not supplied) into each hole, letting the heads extend about 3/16 inch from the wall. Be sure to use screws with heads that fit into the keyhole slots on the bottom of the base.
3.Plug one end of the supplied long modular cord into the modular jack on the back of the base.
4.Route the phone cord through the groove on the bottom of the base, securing the cord under the tabs.
5.Fit the heads of the screw into the keyhole slots, then slide the base down until it is secure.
6.Plug the other end of the cord into a modular phone jack.
on a desktop
1.Plug one end of the supplied long modular cord into the modular jack on the bottom of the base.
2.Route the phone cord through the groove on the base’s bottom. Secure the cord under the tabs along the groove.
3.Plug the other end of the cord into a modular phone jack
Plug one end of the long modular cord here
RINGER ON/OFF
-Slide to the desired setting to enable or disable the ringer when you receive a call.
Liquid Crystal Display - Shows the caller’s phone number with LED light, the time they called, and the
number you dial.
CALL BACK - Press to automatically dial the selected caller ID record.
DELETE - Press to delete the selected caller ID record.
Modular jacks for coiled cord
• You must install the batteries before connecting the |
telephone to the wall jack. If no batteries are installed, |
the telephone and Caller ID still working with no display. |
• If you do not replace the batteries within two minutes, |
your Caller ID and telephone menory information may be |
lost. |
|
|
| VOLUME NORM/HI |
|
|
| - Slide VOLUME to NORM |
|
|
| or HI to adjust the handset |
|
|
| volume to a comfortable |
|
|
| listening level. |
|
|
| LED - the led light red |
|
|
| |
|
|
| when a new phone comes. |
|
|
| TONE/PULSE - Slide to |
|
|
| |
|
|
| the desired setting to select |
|
|
| tone or pulse dialing. |
|
|
| ( REVIEW ) - Press (or ) |
|
|
| to scroll through the stored |
|
|
| caller ID records. |
| what’s included | ||
phone |
| user’s guide | |
connecting the handset
Plug one end of the supplied coiled cord into the handset’s modular jack, and then connect the other end to the jack on the bottom of the telephone base.
Your local RadioShack store sells a variety of longer
NOTE coiled handset cords, which are especially useful when you mount the phone on a wall.
setting the dialing mode
Slide TONE/PULSE to the appropriate setting for your type of service. If you are not sure which service you have, do this simple test.
1.Slide TONE/PULSE to TONE. Lift the handset and listen for a dial tone.
2.Press any number except 0. If your phone requires that you dial an access code before you dial an outside number (9, for example), do not press the access code number.
•If the dial tone stops, you have
•If the dial tone continues, you have pulse service. Slide TONE/PULSE to PULSE.
setting the ringer
connecting the handset
1.Hold down both (REVIEW) for about four seconds until ENTER LANGUAGE, then ENG (flashing) ESP FRA appear.
2.Press ( or ) to select the desired language, then
press DELETE to confirm. LCD CONTRAST and 1 2 3 4 5 appear on the display, and 3 flashes.
3.Press ( or ) to select the contrast level (from
4.Press ( or ) to select the first number of the area code. Press DELETE to confirm the selection.
5.Repeat step 4 to select the second and third digit. ENTER TIME DATE appears and the hour digit flashes.
6.Press ( or ) to select the desired hour, and then
press DELETE to confirm. AM appears for an AM hour, PM appears for a PM hour.
7.Repeat step 6 to set the minutes, month, and day.
NOTE Do not lift the handset from the base until the Caller ID setup has been completed.
using special tone services
require tone signals for communications. If you have pulse service, you can still use special tone service by following these steps.
1.Connect to the special service with TONE/PULSE set to
PULSE.
Please read this user’s guide before
installing, setting up and using your new product
www.radioshack.com
short modular cord | long modular cord |
If you do not want to hear the phone ring, slide RINGER | 2. | When the special service answers, change |
to OFF. You can still make calls with the ringer off, and |
| TONE/PULSE to TONE, or press * to temporarily switch |
you can answer calls if you hear another phone on the |
| to tone dialing. |
same phone line ring. NEW flashes when the phone rings, | 3. | When you complete the call, hang up and return the |
even when the ringer is off. |
| setting to PULSE. |
Note: Actual product may vary from the images found in this document.
