P L A 4 1 7 0 P L A 4 2 7 0
f e a t u r e s a n d c o n t r o l s
4 c h a m p P L A 4 1 7 0 . P L A 4 2 7 0
protection LED |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| power LED |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
ch 3/4 high level inputs
ch 3/4 low level inputs ch 3/4 input level control ch 3/4 crossover mode selector switch
ch 3/4 bass boost level control ch 3/4 low pass frequency control ch 3/4 high pass frequency control
ch 3/4 remote bass boost (PLA4170 without)
ch 1/2 high level inputs
12
ch 1/2 low level inputs ch 1/2 input level control
ch 1/2 crossover mode selector switch ch 1/2 bass boost level control
ch 1/2 low pass frequency control ch 1/2 high pass frequency control
power fuse
f e a t u r e s
4 c h
crossover mode selector when used with normal, full range systems, set this switch to “FULL.” If you wish to use the internal crossover to power a driver of specific frequency range, use the “LOWPASS” or “HIGHPASS” settings.
input level control use this control to match the outputs of your head unit to the amplifier. Starting with your head unit set at about the 2 o’clock position, increase the amp level control until distortion begins to occur, and reduce slightly from this point.
low pass frequency control when the crossover selector switch is in “low pass” mode, this control sets the upper frequency limit for audio program sent to the speakers.
high pass frequency control when the crossover selector switch is in “high pass” mode, this control sets the lower frequency limit for audio program sent to the speakers.
Remote Bass Boost Plug in the Remote Bass Boost Control wire in here.
bass boost level control this control permits adjustment of the bass level up to an increase of approximately 18 dB.
low level inputs this amp features
high level inputs if your car stereo lacks
power LED this indicator is illuminated when power is applied.
protection LED this indicator is illuminated when
power fuse the fuse protects the amplifier and your car’s electrical system from short circuit conditions.
power terminals use these connectors to deliver power, ground and remote
speaker connections these terminals are 14K gold plated to guarantee high conductivity and minimum signal loss.
speaker connections
power terminals
a n d s p e c i f i c a t i o n s
a m p P L A 4 1 7 0 . P L A 4 2P 7L0A 4 1 7 0 | P L A 4 2 7 0 | |
| 4 channel amplifier | 4 channel amplifier |
output power @ 14.4v DC, 1KHz |
|
|
RMS Power @ 4 Ohms | 35 Watts x 4 | 75 Watts x 4 |
RMS Power @ 2 Ohms | 50 Watts x 4 | 110 Watts x 4 |
Maximum Power Output | 250 Watts x 4 | 400 Watts x 4 |
frequency response | 15 |
|
input impedance |
|
|
low level inputs | 10K Ohms |
|
high level inputs | 100 Ohms | 13 |
input sensitivity |
| |
|
| |
low level inputs | 250mV |
|
high level inputs | 2.5V |
|
power supply voltage | 14.4V DC Neg. Ground |
|
matching speaker impedance |
|
|
stereo mode |
| |
bridged mode |
| |
maximum current draw | 30A | 40A |
dimensions (W x H x L) |
|
|
mm | 292 x 60 x 305 | 292 x 60 x 432 |
inches | 11.5 x 2.34 x 12 | 11.5 x 2.34 x 17 |
