don't try to repair it, call a qualified service technician. Force or attempted repair may result in a fire or explosion.
D.Do not use this boiler if any part has been under water. Immediately call a qualified service technician to inspect the boiler and to replace any part of the control system and any gas control which has been under water.
FOR STANDING PILOT MODELS WITH ROBERT- SHAW GAS VALVE, 2 STAGE OPERATION. (Models 90, 135 & 180)
1. STOP! Read the safety information.
2. Set the thermostat to the lowest setting.
3. Turn off all electric power to the appliance.
4. Push in and move gas control lever counter-
clockwise | to "OFF" position. | ||
GAS CONTROL |
|
| |
LEVER SHOWN |
|
| |
IN "OFF" POSITION |
|
| |
GAS INLET |
|
| Fig.#8934.0 |
|
| ||
|
|
| |
NOTE: Lever cannot be moved from "ON" to "OFF" unless lever is pushed in slightly. Do not force.
5. Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow "B" in the safety information above on this label. If your don't smell gas, go to the next step.
6. Locate pilot mounted on the right side of the burner drawer, and right of first burner.
THERMOCOUPLETHERMOCOUPLE
ROBERTSHAW PILOT | HONEYWELL PILOT | |
Fig.#8084.1 |
| Fit. # 8083.0 |
7. Move control lever clockwise to | "SET" | |
position and immediately light pilot with a match. 8. Hold lever in "SET" position for 1/2 minute after
pilot is lit. Release lever, and it will spring back to "PILOT" position Pilot should remain lit. If it goes out, repeat steps 4 through 8.
*If lever does not spring back to "PILOT" position when released, stop and immediately call your
service technician or gas supplier.
*If the pilot does not stay lit after several tries, move the gas control lever to "OFF" and call your service technician or gas supplier.
9. Stand to the side of the heater and move the gas
control lever counterclockwise | to "ON". |
10.Turn on all electric power to the appliance.
11.Set the thermostat to the desired setting.
TO TURN OFF GAS TO THE BOILER
1. Set the thermostat to the lowest setting.
2. | Turn off all electric power to the appliance. | |
3. | Push in and move gas control lever counter- | |
| clockwise | to "OFF" position. Do not |
| force. |
|
LIGHTING INSTRUCTIONS FOR AUTOMATIC IGNITION MODELS.
Please read carefully and understand the following safety information before operating the boiler.
WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing prop- erty damage, personal injury or loss of life.
A.This boiler does not have a pilot. It is equipped with a hot surface ignition device which automatically lights the burners. Do not try to light the burners by hand.
B.BEFORE OPERATING smell all around the boiler area for gas. Be sure to smell next to the floor because some gases are heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
*Do not try to light any appliance.
*Do not touch any electric switch;
*Do not use any phone in your building.
*Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions.
*If you cannot reach your gas supplier, call the fire department.
C.Use only your hand to push in, move or turn the gas control knob or lever. Never use tools. If the knob or lever will not push in, move or turn by hand, don't try to repair it, call a qualified service technician. Force or attempted repair may result in a fire or explosion.
D.Do not use this boiler if any part has been under water. Immediately call a qualified service technician to inspect the boiler and to replace any part of the control system and any gas control which has been underwater.
2
