RCA 600-Watt manual MANUFACTURER’S Codes, Using the Sleep Timer, TV Codes

To control the satellite receiver or cable box with the remote control, see “Using the Remote Control to Control Additional Components” on Page 22.

USING THE SLEEP TIMER

You can set the sleep timer to turn off the receiver after a set period of time.

Repeatedly press SLEEP to set the sleep timer to the desired time ('&, (&, )&, *&, +&, ,&, -&, .&, or /& minutes or OFF). When the desired sleep time appears, let the sleep timer time out (do not press SLEEP again). The display dims when the sleep timer is set.

To check the expired sleep time, press SLEEP once. The remaining time appears. To continue the sleep time, let it time out. To cancel the sleep timer, press SLEEP repeatedly until it turns off.

The receiver turns off when the selected time has expired.

Note: To brighten the display while the sleep timer is on, press DIMMER (on the receiver).

USING THE REMOTE CONTROL TO CONTROL ADDITIONAL COMPONENTS

You can set your remote control to control other components such as a VCR, TV, satellite receiver or cable box.

1.Turn on the component to be programmed.

2.Look up the brand and corresponding code(s) in the code list (see “Manufacturer’s Codes” on Page 22).

3.While holding down the appropriate source button (VCR, TV, or SAT) on the remote control, use the number keys to enter the first code from the code list.

4.Release the source button, then press POWER. If you have entered the correct code, the component turns off.

If the component does not turn off, repeat Steps 3 and 4 and use the next code (if applicable) listed for the brand of your component until the component responds to the remote command.

5.Experiment with the remote control and your components to see which buttons work. If only a few functions operate, repeat Step 4 to see if another code operates more buttons.

Notes:

•To turn on or off the receiver when you select the VCR, SAT, or TV function, press POWER twice.

•Once the manufacturer’s code for the TV is set, MUTE and VOLUME +/– can only be used in TV mode.

Cautions:

•This remote control might not operate on all models of the brands shown in the “Manufacturer’s Codes” on Page 22.

•If batteries are removed from the battery compartment of the remote, replace the batteries within 30 minutes or the codes are lost. You must then re-enter all previously programmed codes.

•The buttons on the remote control may not work exactly like the component’s corresponding buttons.

MANUFACTURER’S CODES

TV Codes

Brand	Codes
ABEX	272
ADMIRAL	101
AKAI	102
ALLERON	146
AMTRON	138
AOC	104,105,106,107
AUDIOVOX	138
BELCOR	104
BELL & HOWELL	101, 262
BRADFORD	138
BROCKWOOD	104
CANDLE	104, 106, 108
CELEBRITY	102
CITIZEN	104, 106, 108, 138, 205, 271
COLORTYME	104, 106
CONCERTO	104, 106
CONTEC/CONY	112, 113, 138
CRAIG	138
CROWN	138, 271
CURTIS MATHES	104, 106, 115, 185, 205, 262, 271
CXC	138
DAEWOO	104, 105, 106, 117, 118, 271
DAYTRON	104, 106, 271
DIMENSIA	185
DUMONT	104
ELECTROBAND	102
ELECTROHOME	103, 104, 106, 119, 122
EMERSON	104, 106, 112, 124, 125, 126, 127, 128,
	129, 130, 131, 132, 134, 135, 136, 138,
	139, 141, 142, 146, 262, 271, 279
ENVISION	104, 106
FISHER	148, 149, 151, 262, 280
FUJITSO	146
FUNAI	138, 146

22