CAR/PERSONAL CD PLAYER
WITH ELECTRONIC SKIP PROTECTION
RP-2215
FEDERAL COMMUNICATIONS COMMISSION (FCC) INFORMATION
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
In accordance with FCC requirements, changes or modifications not expressly approved by Thomson Consumer Electronics could void the user’s authority to operate this product.
This device generates and uses radio frequency (RF) energy, and if not installed and used properly, this equipment may cause interference to radio and television reception.
If this equipment does cause interference to radio or television reception (which you can determine by turning the equipment off and on), try to correct the interference by one or more of the following measures:
• Reorient the receiving antenna (that is, the antenna for the radio or television that is | |
| “receiving” the interference). |
• | Move the unit away from the equipment that is receiving interference. |
• | Plug the unit into a different wall outlet so that the unit and the equipment receiving |
POWERING UP
There are three ways to power your CD player:
BATTERY OPERATION
| + | – |
FOR ALKALINE BATTERIES: | – | + |
1.Slide the battery door on the bottom of the unit to the left to open.
2.Insert 2 "AA" batteries with the correct polarities into the battery compartment.
3.Close the battery door.
NOTE: The unit will not work, and the batteries will be drained and/or depleted if not inserted as shown above.
FOR NICKEL-CADMIUM (NICAD) BATTERIES:
This unit is equipped with battery recharging circuitry. For safety measures, it requires two specifically made NICAD
It is always a good idea to let
TO CHARGE NICAD BATTERIES:
1.Install
2.Connect the AC adapter to the DC 6V input jack.
WARNING: Use the DC 6V input jack only if you have rechargeable
installed. DO NOT CONNECT AN AC ADAPTER TO THE DC 6V INPUT JACK IF YOU HAVE
NON-RECHARGEABLE BATTERIES INSTALLED.
If you try to recharge
3.Plug the AC adapter into an AC wall outlet and the CHARGING indicator lights up. The batteries are now being recharged while the unit draws power from the AC wall outlet.
4.After 15 hours (approx.), unplug the adapter from the wall outlet and disconnect it from the unit.
NOTE: DO NOT charge for more than 24 hours. Excessive charging may adversely affect the performance of the rechargeable batteries.
AC ADAPTER OPERATION
You can power your CD player with the AC adapter from any AC outlet
when they are installed in the battery compartment while the unit is operating by AC power. To use the AC adapter, insert the plug of the adapter into the DC IN 6V jack on the right side of the unit. Plug the adapter into an AC wall outlet.
NOTE: The CD player won’t run on batteries if the AC adapter is still plugged into the DC IN 6V jack.
CAR (DC) POWER SUPPLY ADAPTER
Plug the Car (DC) power supply adapter into the DC IN 6V jack on the right side of the CD player, and then into the cigarette lighter receptacle in your car.
USING HEADPHONES
Your CD player has been equipped | Have a Blast – Just Not in Your Eardrums | |
with a PHONES (green) jack on the | Make sure you turn down the volume on the unit | |
left side of the unit. Insert the | ||
before you put on headphones. Increase the volume to | ||
plug of the headphone set into the | the desired level only after headphones are in place. | |
jack for private listening. |
|
PLAYING A DISC
1.Connect the headphones via the PHONES (green) jack and turn the volume all the way down.
2.Press the OPEN button to open the CD compartment door and insert the CD of your choice making sure the label side is facing up.
3.Press the “PUSH CLOSE” mark on the right side of the CD compartment door to close it.
4.Slide the HOLD switch to the “off” position.
5.Press the PLAY/PAUSE button to begin CD play.
The LCD will show the total number of tracks and playing time of the loaded disc before starting to play it. During play, the LCD will show the current track number and its elapsed playing time.
6.Adjust the volume to your desired level.
7.Press the PLAY/PAUSE button again to temporarily suspend disc activity. The LCD will flash. Press the button a third time to resume disc activity.
8.Press the STOP button to end all disc activity.
NOTE: This unit is capable of playing a 3" CD single without an adapter.
REPEAT PLAY
TO REPEAT ONE:
1.Press the P.MODE button until the Repeat 1 indicator (
1) is displayed.
2.Choose the track you want to hear using the SKIP/SEARCH buttons, then press the PLAY/PAUSE button to start play mode.
The unit will play the selected track to its end, automatically return to its beginning and play it again.
TO REPEAT ALL:
Press the P.MODE button until the Repeat All indicator (
ALL) is displayed.
The unit will play the disc from start to finish, return to the beginning and play it again.
RANDOM PLAY
Press the P.MODE button until the Random indicator is displayed. The unit will play all tracks out of sequence once.
INTRO PLAY
1.Press the P.MODE button until the Intro indicator flashes in the display.
2.Press the PLAY/PAUSE button to activate the Intro feature.
The unit will play the first 10 seconds of each track on the disc and then stop automatically.
PROGRAM PLAY
1.Press the P.MODE button until the program indicator “M” flashes in the display.
2.Press the SKIP/SEARCH buttons to choose the track you want to hear.
3.Press the SET button to store the track number in that memory location. The next memory location will flash in the display.
4.Repeat Steps 2 and 3 to store up to 22 tracks.
5.Press the PLAY/PAUSE button to start the Program Play mode.
When the last track has played, the unit will automatically stop.
PROGRAM REPEAT PLAY
1.Press the P.MODE button until the program repeat indicator (
M) flashes in the display.
2.Follow Steps
When the last track has finished playing, the unit will automatically return to the beginning of the program and play it again.
TO CHECK PROGRAM PLAY LIST
1.Press the P.MODE button until the program memory indicator “M” appears in the display.
2.Press the SET button to scroll through the programmed tracks one by one in order.
Problem | Cause | Solution |
Sound skips. | Disc is damaged. | Insert a new disc. |
| Excessive external vibration. | Find a more stable position. |
|
|
|
Disc is in place, player is in | Requires headphones | Put on headphones. |
play mode, but still no sound. | or external amplifier. | Adjust volume. |
| Poor connections. | Check connections. |
| PAUSE is active. | Press PLAY/PAUSE to put in play |
|
| mode. |
|
|
|
Unit will not scan the disc. | Batteries are weak. | Replace batteries or try AC/DC |
Play is erratic |
| power. |
| Dirty or damaged disc. | Replace or clean the disc. |
|
|
|
CARE AND MAINTENANCE
•Do not touch the laser lens.
•Temperature changes can cause condensation to form on the laser lens. If condensation forms on the lens, leave the disc compartment door open (with no disc) for an hour to remove condensation.
•Exposure to direct sunlight or extreme heat (such as inside a car parked in the sun) can cause damage or malfunction.
•To prevent dust from reaching internal parts, keep the disc compartment door closed when not in use (except when necessary to remove condensation).
•Do not place objects on top of the player.
CLEANING THE LASER LENS
It’s important that you periodically clean the laser lens, especially when dust or fingerprints are evident. Not cleaning the laser lens can result in inferior sound quality or no sound at all. To clean the lens, follow these directions:
1. | Turn off the unit’s power. | Laser |
|
| |||
2. | Open the disc compartment and remove the disc (if there is one). | lens |
|
|
| ||
3. | Clean the lens with a soft brush or use a camera air blower brush. |
|
|
4.If you still are not able to remove dirt particles, moisten a cotton swab with
isopropyl alcohol and gently apply to the face of the laser lens, rubbing gently until all traces of dirt are removed.
HANDLING COMPACT DISCS
To get the best possible sound from your compact discs, you need to keep them clean. Note the following guidelines regarding the use and care of compact discs:
•Don’t touch the playing surface (the side without the label).
•Don’t store discs in places with high temperatures or high
•Don’t put tape or any other adhesives on either side of the disc.
•Don’t use cleaners or
•Always store each disk in its case and not in the CD player.
•Before playing a disc, wipe any dust or fingerprints from the playback surface with a soft cloth. Wipe from the hub to the edge with a straight motion.
PRECAUTIONS
•Never open the cabinet under any circumstances. Any repairs or internal adjustments should be made only by a trained technician.
•Warning: Never operate this product with the cabinet removed.
•Do not touch the player with wet hands. If any liquid enters the player cabinet, take the player to a trained technician for inspection.
•This compact disc player uses a laser to read the music on the disc. The laser mechanism corresponds to the cartridge and stylus of a record player. Although this product incorporates a laser
•Discs rotate at high speed inside the player. Do not use damaged, warped, or cracked discs.
interference are on different branch circuits. |
If these measures do not eliminate the interference, please consult your dealer or an experienced radio/television technician for additional suggestions. Also, the Federal Communications Commission has prepared a helpful booklet, “How To Identify and Resolve Radio TV Interference Problems.” This booklet is available from the U.S. Government Printing Office, Washington, DC 20402. Please specify stock number
This product complies with DHHS Rules 21 CFR Subchapter J. Applicable at the date of manufacture.
P.O. Box 1976, Indianapolis, IN 46206 | Model |
© 1998 Thomson Consumer Electronics, Inc. | |
Trademark(s) ® Registered | 20906610 (E/S Rev. 1) |
Marca(s) Registrada(s) | Printed in Hong Kong |
IMPORTANT BATTERY INFORMATION
•Do not mix different types of batteries, such as an alkaline with a NiCad, or use new batteries with old ones.
•Be sure to follow the polarity
•Alkaline batteries are good for about 10 hours of continuous CD play. Rechargeable batteries substantially reduce play time.
•For safety measures, it requires two specially made NICAD
•Using
•Rechargeable batteries other than
•If you’re not going to use your player for a month or more, be sure to remove batteries because they can leak and damage the unit.
Rechargeable batteries may slowly lose their charge when stored, therefore an initial charge may be required before use.
•Dispose of batteries in the proper manner, according to federal, state, and local regulations.
•Any battery may leak electrolyte if mixed with a different battery type, if inserted incorrectly, if all batteries are not replaced at the same time, if disposed of in fire, or if an attempt is made to charge a battery not intended to be recharged.
•Discard leaky batteries immediately. Leaking batteries can cause skin burns or other personal injury.
•Remember that battery life is directly correlational to volume and bass listening levels. If you use the volume and bass features at maximum levels, your batteries will operate at maximum consumption.
HEADSET SAFETY
•Do not play your headset at a high volume. Hearing experts advise against continuous extended play.
•If you experience a ringing in your ears, reduce volume or discontinue use.
•Do not use while operating a motorized vehicle or bicycle, it may create a traffic hazard and is illegal in many areas.
•You should use extreme caution or temporarily discontinue use in potentially hazardous situations.
•Even if your headset is an
CONNECTING TO AUDIO SYSTEMS
Your CD player has been equipped with a LINE OUT (black) jack on the left side of the unit to allow it to operate in conjunction with another audio system. Using an audio line cable - not included - plug one end into the LINE OUT (black) jack on your CD player and other into the CD/AUX input(s) jack on the audio system.
FEATURES
VOLUME
Use the dial on the left side of the player to control the volume. Remember that you should always set the volume to the minimum level before putting on your headphones, and then adjust the setting to a desired level.
HEADPHONES
Insert the plug of the headphone set into the PHONES (green) jack on the left side of the unit.
PLAY/PAUSE 
Press the PLAY/PAUSE button once to begin Play mode. Press again to pause play. The track number will flash in the display while the disc is paused. Press a third time to resume Play mode.
STOP 
Press the STOP button once to stop Play mode, after which power will turn off automatically.
SKIP/SEARCH 
/ 
Press 
once to skip to the beginning of the current track or repeatedly to skip to previous tracks. Press and hold during play to search backward at high speed within the current track. Play resumes when button is released.
Press 
once to skip forward to the beginning of the next track or repeatedly to skip forward to the beginning of other tracks. Press and hold during play to search forward at high speed within the current track. Play resumes when button is released.
DBBS (DYNAMIC BASS BOOST SYSTEM)
DBBS is used to enhance low frequency (bass) levels. Make sure you set the volume to minimum before activating the DBBS, then adjust to your desired level.
P. MODE
Press during play to choose various play modes available. Press once to Repeat One track. Press again to Repeat All tracks. Press three times to activate the INTRO feature and hear the first 10 seconds of each track on the CD. Press four times to play the tracks in Random order. Press five times to activate Program Repeat and six times to activate Program Play.
HOLD
Use this switch to prevent accidental activation of unwanted functions while the unit is in Play or Stop mode. The "on" position disables all function buttons, while the "off" position enables all function buttons for normal operation.
LCD (LIQUID CRYSTAL DISPLAY)
The LCD will always display the number and elapsed time of the track playing while the disc is active.
In pause mode, the elapsed time will flash. The battery symbol (
) is displayed when the unit is
being powered by batteries. (
) blinks in the display when batteries are weak or running low.
ANTI SKIP (ELECTRONIC SKIP PROTECTION)
The Electronic Skip Protection (ESP) system keeps your CDs from skipping when the player is jarred. Note that ESP consumes additional power and wears down batteries more quickly. Thus it is recommended to set the ESP off when the player is used in
Press the ANTI SKIP button to activate the feature. The ESP symbol appears in the LCD and fills up with dots as the player stores music into memory. When the player is jarred, the memory is used and the dots on the ESP symbol disappear one at a time. If the player undergoes continual jarring that clears all of the dots, the music stops until the memory can be filled again; then it continues playing where it left off.
TO CHANGE THE PROGRAMMED PLAY LIST
1.Press the SET button to find the track you want to replace.
2.Select a new track by pressing one of the SKIP/SEARCH buttons.
3.Press the SET button again to set the changes.
4.To start the Program Play mode, press the PLAY/PAUSE button.
TO CLEAR THE PROGRAMMED CONTENTS
Press the STOP button or OPEN button to clear the program.
LISTENING TO CDS IN YOUR CAR
ADJUSTING THE LINE CORD
Because tape decks vary, you may need to adjust the line cord on the Cassette adapter in order to get the cassette adapter to fit correctly into your car’s tape deck.
1. Gently pull the cord out of the restraining channel.
2. Change the cord orientation to fit your car stereo orientation.
3. Push the cord into place in the restraining channel.
PLAYING COMPACT DISCS
1. Select a power source (either battery power or the Car DC
3. Set your car stereo volume to a low level.
4. Insert a compact disc and press PLAY. Adjust CD player’s volume to a mid level (make sure DBBS is turned off).
5. Use the car stereo to adjust the volume, tone, etc. You may need to adjust the volume on your CD player if you hear clicks or other distortion.
6. Before ejecting the cassette when you’re finished, make sure the car stereo’s volume is turned down.
REMOVING A DISC
1.Press the STOP button to end all disc activity.
2.Press the OPEN button to open the CD compartment door.
3.Grasp the CD by its edge while gently press down on the unit's center spindle.
4.Lift the CD from the edge and remove it from the compartment.
TROUBLESHOOTING GUIDE
Problem | Cause | Solution |
Disc is in place, | No power. | Make sure power adapter is |
but won’t play. |
| getting power from outlet or |
|
| install fresh batteries. |
| Disc is in upside down. | Insert disc with label up. |
| Disc is dirty. | Clean the disc or try another |
|
| disc. |
| Batteries are weak. | Replace batteries or try AC/DC |
|
| power. |
| Adapter plugged into jack | Remove adapter from player to |
| but not into power source. | use with batteries, or plug into |
|
| outlet. |
| CD door is not closed tightly. Close door tightly. | |
| Disc not seated correctly. | Press down firmly . |
|
|
|
SERVICE INFORMATION
This product should be serviced only by those specially trained in appropriate servicing techniques.
FOR YOUR RECORDS
In the event that service should be required, you may need both the model number and the serial number. In the space below, record the date and place of purchase, and the serial number:
Date of Purchase ___________________________________________________________________________
Place of Purchase __________________________________________________________________________
Serial No. _________________________________________________________________________________
LIMITED WARRANTY
What your warranty covers:
• Any defect in material or workmanship.
For how long after the original purchase:
RP 7925 | • One year. |
| (The warranty period for rental units begins with the first rental or 45 days from date of |
| shipment to the rental firm, whichever comes first.) |
| What we will do: |
| • Provide you with a new or, at our option, a refurbished unit. |
| • The exchange unit is warranted for the remainder of your product’s original warranty period. |
| How to make a warranty claim: |
| • Properly pack your unit. Include any cables, etc., which were originally provided with the |
| product.We recommend using the original carton and packaging materials. |
| • Remove cassette tapes or CDs from unit before shipping as these will not be returned. |
| • Include in the package evidence of purchase date, such as the bill of sale. Also print your |
| name and address and a description of the defect. Send standard UPS or its equivalent to: |
| Thomson Consumer Electronics, Inc. |
| Product Exchange Center |
| 32B Spur Drive |
| El Paso, Texas 79906 |
| • Pay any charges billed to you by the Exchange Center for service not covered by the |
| warranty. |
| • Insure your shipment in case of loss or damage. Thomson accepts no liability in case of |
| damage or loss. |
| • A new or refurbished unit will be shipped to you by prepaid freight. |
| What your warranty does not cover: |
•Customer instruction. Your owner's manual provides information regarding the operating instructions and user controls. For additional information, ask your dealer.
•Installation and setup service adjustments
•Batteries
•Damage from misuse or neglect
•Products that have been modified or incorporated into other products.
•Product purchased or serviced outside the USA
•Acts of God, such as but not limited to lightning damage.
Product Registration:
•Please complete and mail the Product Registration Card packed with your unit. It will make it easier to contact you should it ever be necessary. The return of the card is not required for warranty coverage.
How state law relates to this warranty:
•This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
If you purchased your product outside of the U.S.A:
• This warranty does not apply. Contact your dealer for warranty information.
