ASSEMBLY
Assembly requires two persons. Place all parts of the elliptical crosstrainer in a cleared area and remove the packing materials. Do not dispose of the packing materials until assembly is completed.
Assembly requires the included allen wrench | and two adjustable wrenches of your own | . | ||
1. The Console (43) requires two ÒAAÓ batteries (not |
| 1 |
|
|
included). Alkaline batteries are recommended. |
|
|
| |
|
|
|
| |
To install batteries, look under the Console (43) and | 43 |
|
| |
locate the battery door. Refer to the inset drawing. |
|
|
|
|
Press the tab on the battery door and remove the |
| Battery |
|
|
battery door. Insert two batteries into the Console. |
| Door |
|
|
Make sure that the negative ends of the batteries |
|
|
| |
(marked ÒÐÓ) are touching the springs in the |
| Battery |
|
|
Console. When the batteries are correctly installed, |
|
| ||
Door |
|
| ||
|
|
| ||
|
|
|
| |
|
| Tab |
| Batteries |
|
|
|
| |
2. While another person holds the Upright (6) in the |
| 2 |
|
|
position shown, connect the Upper Wire Harness |
|
|
|
|
(27) to the Lower Wire Harness (28). |
|
|
|
|
Carefully slide the Upright (6) onto the Frame (1). Be |
| 6 |
| |
careful to avoid pinching the Wire Harnesses (27 |
|
| ||
|
|
| ||
and 28). Tighten a 3/8Ó Button Head Screw (64) with | 64 |
|
| |
a 3/8Ó Lock Washer (66) into the front of the Upright |
|
| ||
|
|
| ||
and the Frame. Next, tighten two 3/8Ó Button Head |
| 66 |
| 64 |
Screws (64) with 3/8Ó Lock Washers (66) into the |
|
|
| |
|
|
|
| |
sides of the Upright and the Frame. Note: It may be | 64 | 66 |
| |
necessary to loosen the front Button Head Screw |
|
| ||
|
|
|
| |
slightly in order to attach the other two Button Head |
|
| 27 |
|
Screws. Firmly tighten all three Button Head |
|
| 28 |
|
Screws. |
|
|
| |
|
| 1 |
| |
|
|
|
| |
3. Make sure that there are two 5/16Ó Bushings (29) in | 3 |
|
| |
|
|
| ||
the front end of the Right Outer Leg (2). Attach the |
|
|
|
|
Right Handlebar (4) to the Right Outer Leg with a |
|
|
| 4 |
5/16Ó x 1 3/4Ó Hex Bolt (61) and a 5/16Ó Nylon Jam |
|
| 5 |
|
Nut (84). Make sure that the head of the Bolt is on |
|
|
| |
|
| 3 | 84 | |
the inside of the Right Handlebar as shown. |
|
| ||
|
|
| ||
Attach the Left Handlebar (5) to the Left Outer Leg |
|
| 61 | 2 |
|
|
|
| |
(3) in the same way. |
| 1 |
|
|
|
|
|
| |
Push the four 2Ó x 3Ó Endcaps (38) onto the Frame |
| 38 |
| 29 |
|
|
|
| |
(1). |
|
|
|
|
4.Make sure that all parts of the elliptical crosstrainer are properly tightened. To protect the floor or carpet from damage, place a mat under the elliptical crosstrainer.
5
