MAINTENANCE
6) | Do not permit creosote or soot buildup in the |
| chimney system. Check and clean chimney |
| at regular intervals. |
7) | Your Regency Insert can be very hot. You |
| may be seriously burned if you touch the |
| insert while it is operating. Warn children of |
| the burn hazard. |
8) | The insert consumes air while operating, |
| provide adequate ventilation with an air |
| duct or open a window while the insert is |
| in use. |
9) | Do not use grates, irons or other methods |
| for supporting fuel. Burn directly on the |
Removal for Cleaning etc.
Removal of your insert for cleaning purposes is usually not required if a proper installation has been done. In the event that removal is re- quired, be sure not to damage any parts needed for
WARNING: Thingstorememberincase of chimney fire:
1)Close draft control
2)Call the Fire Department
DOOR LATCH
ADJUSTMENT
The door latch may require adjustment as the door gasket material compresses after a few
fires. Removal of the spacer washer, shown in the diagram below, will allow the latch to be moved closer to the door frame, causing a tighter seal. Remove and replace the nuts, washer as shown.
bricks. |
10) Open the draft control fully for 10 to 15 |
seconds prior to slowly opening the door |
when refuelling the fi re. |
11) Do not connect your unit to any air distribu- |
tion duct. |
12) Your insert should burn dry, standard fi re- |
wood only. The use of “mill ends” is discour- |
aged as this fuel can easily overheat your |
insert. Evidence of excessive overheating |
will void your warranty. As well, a large |
portion of sawmill waste is chemically |
treated lumber, which is illegal to burn in |
many areas. Chemically treated fi re logs |
also must not be burned in your insert. |
13) Do not store any fuel closer than 2 feet from |
your unit. |
14) Do not burn salt drift wood as it will corrode |
your unit and void the warranty. |
15) Do not operate the unit if the glass is broken |
or missing. Do not operate the unit if the |
gasketing is worn out and not sealing the |
door or the glass. |
It is very important to carefully maintain your insert, including burning seasoned wood and maintaining a clean stove and chimney system. Have the chimney cleaned before the burning season and as necessary during the season, as creosote deposits may build up rapidly. Moving parts of your insert require no lubrication.
CREOSOTE
When wood is burned slowly, it produces tar and other organic vapors, which form creosote when combined with moisture. The creosote vapors
Ways to Prevent and
Keep Unit Free of Creosote
1)Burn insert with draft control wide open for about15minuteseverymorningduringburn- ing season. This helps to prevent creosote deposits within the heating system.
2)Burn insert with draft control wide open for about 10 - 15 minutes every time you add fresh wood. This allows the wood to achieve the charcoal stage faster and burns up any wood vapors which might otherwise be deposited within the system.
3)Only burn seasoned wood! Avoid burning wet or green wood. Seasoned wood has been dried at least one year.
4)A small hot fi re is preferable to a large smouldering one that can deposit creosote within the system.
5)Check the chimney at least twice a month during the burning season for creosote
6)Have chimney system and unit cleaned by competent chimney sweeps twice a year during the fi rst year of use and at least once a year thereafter or when needed.
MAINTENANCE OF
The gold electroplated fi nish on the doors requires little maintenance, and need only be cleanedwithadampcloth.DONOTuseabrasive materials or chemical cleaners, as they may harm the fi nish and void the warranty.
GLASS CLEANING
Only clean your glass window when it is cool. Your local retailer can supply you with special glass cleaner if plain water and a soft cloth does not remove all deposits.
GLASS
REPLACEMENT
Your Regency Insert is supplied with 5 mm. Neoceram ceramic glass that will withstand the highest heat that your unit will produce. In the event that you break your glass by impact
-purchase your replacement from an authorized
GLASS REMOVAL
Allowthestovetocoolbeforeremovingorreplac- ing glass. Remove the door from the insert and remove the glass retainer. Use caution when removing broken glass to prevent injury.
When placing the replacement glass in the door, make sure that the glass gasketing will properly seal your unit. Replace the retainer and tighten securely, but do not wrench down on the glass as this may cause breakage. Do not substitute materials. If your glass door does break, do not continue to use your unit until it has been replaced.
condense in the relatively cool chimney fl ue of a
DOOR GASKET
If the door gasket requires replacement, 7/8" diameter material must be used. A proper high temperature gasket adhesive is required. A gasket repair kit, Part #
14 | Regency Wood Insert & Hearth Heater |