Faceplate and Trim, H2100M and I3100L Insert

INSTALLATION

4)If the ﬂ oor of your ﬁ replace is below the level of the ﬁ replace opening, adjust the insert's levelling bolts to accommodate the difference. When additional shimming is required, use non-combustible masonry or steel shims.

5)Measure approximately the alignment of the ﬂ ue liner with the position of the smoke outlet hole on the insert to check for pos- sible offset. If an offset is required, use a proper stainless steel unit available with the chimney liner.

3)Attach the assembled faceplate to the faceplate mounting brackets.

Diagram 2: I1100S

Rear View

B) H2100M and I3100L Insert

Flush Inserts

Hearth Heater

Diagram 4:

H2100M and I3100L

Faceplate Assembly

6)Once the above items have been checked, slide your insert into position after ﬁ rst po- sitioning the ﬂ ue liner and offset if required. (Re-install raincap at completion of installa- tion).

FACEPLATE AND TRIM

Prior to sliding your insert into its ﬁ nal position and attaching the connector or liner pipe, the faceplate side panel plates must be installed as follows:

A) I1100S Small Insert

Diagram 3: I1100S

C) All units

The unit may now be slid into ﬁ nal position and attached to the connection system.

Once connection is made, the insulation strips should be installed between the insert faceplates and the ﬁ replace face. The faceplate top may now be installed (with insulation strip behind) by aligning its brackets with the top ﬂ ange on the side shields and the angle iron bar on the insert top. The faceplate trim may be installed to the edge of the faceplate at this time.

1)Fasten the faceplate mounting bracket to the side of the insert (one on each side) using the screws provided (2 screws per bracket) (refer to Diagram 1).

2)Assemble the faceplate sides and top with 4 screws (see Diagram 2).

1)Slide the spring nuts (supplied) over the slots in the insert’s side convection panels (the spring nuts may need to be squeezed with a pair of pliers ﬁ rst, to help them stay in position).

2)Screw the side faceplate panels, (item A in Diagram 4) one to each side.

3)Using the top panel (item B in the diagram) as a gauge, check that the side panels are withinapproximately1/4"oftheoverallwidth. If the difference is greater than this, use the supplied washers to attain the required width.

I1100S: Drill two 5/32" diameter holes through the trim and side panels and screw the trim to the panels using the gold plated screws provided.

Note: It may be easier to install the insula- tion, faceplate top and faceplate trim withtheunitpulledslightlyawayfrom the ﬁreplace face. If this is done, be very careful not to disturb the con- nector when shifting the unit to its ﬁnal position.

Now that your insert is installed, check once more that all the clearances from the unit to any combustible materials are correct as listed earlier.

Diagram 1: I1100S

Regency Wood Insert & Hearth Heater

I1100S specifications

The Regency I1100S is a remarkable piece of technology that epitomizes modern design and functionality. Tailored for individuals who seek both performance and aesthetics in their audio devices, the I1100S delivers an impressive sound experience while embodying an elegant and contemporary style.

One of the standout features of the Regency I1100S is its high-fidelity audio output. Sporting advanced audio processing technologies, this device ensures that listeners enjoy crisp highs and deep lows, capturing the full spectrum of sound with clarity and precision. Whether it’s music, podcasts, or audiobooks, the I1100S offers an immersive listening experience, making it a perfect companion for both casual listeners and audiophiles alike.

Another key characteristic of the I1100S is its wireless capabilities. Equipped with Bluetooth technology, the device allows users to stream audio directly from their smartphones, tablets, or computers without the hassle of cords. This wireless freedom enhances convenience, allowing users to move about freely while still enjoying their favorite sounds.

The I1100S also prioritizes usability with its user-friendly interface. Intuitive controls and a clear display make navigating through tracks and settings a simple task. The one-touch operation allows for quick responses, ensuring that users can switch songs or adjust volumes seamlessly, without distraction from their listening experience.

Durability and design are important aspects of the I1100S as well. Crafted with high-quality materials, it features a robust build that can withstand everyday use. Its sleek design complements any environment, whether placed in a living room, office, or on a bookshelf. Available in a variety of finishes, users can select a look that best suits their personal style.

In terms of connectivity, the Regency I1100S offers multiple input options, including USB and auxiliary ports, providing versatility for various playback devices. This means that whether users want to connect a traditional audio device or use modern streaming methods, they have the flexibility to do so.

Lastly, the I1100S is designed with energy efficiency in mind. It operates on low power consumption without compromising sound quality, making it an environmentally friendly choice in audio technology.

In summary, the Regency I1100S is more than just an audio device; it's a sophisticated blend of cutting-edge technology, user-centric design, and aesthetic appeal. With its outstanding audio performance, wireless capabilities, and durable construction, the I1100S stands out in the competitive landscape of modern audio solutions, catering to the needs of diverse users seeking both quality and style.

Regency Faceplate and Trim, H2100M and I3100L Insert, I1100S Small Insert, All units

Models: I1100S