MAINTENANCE
MAINTENANCE
INSTRUCTIONS
1) Always shut the valve off before cleaning. |
For relighting, refer to lighting instructions. |
Keep the burner and control compartment |
clean by brushing and vacuuming at least |
once a year. When cleaning the logs, use |
a soft clean brush as the logs are fragile |
and easily damaged. |
2) Clean glass (never when unit is hot), ap- |
pliance, louvers, and door with a damp |
cloth. Never use an abrasive cleaner. The |
gold louvers (and optional gold door) may |
be scratched if abrasives are used to |
clean them. |
The heater is finished in a heat resistant |
paint and should only be refinished with |
CLOTHING OR OTHER FLAMMA- BLE MATERIAL SHOULD NOT BE PLACEDONORNEARTHEAPPLI- ANCE.
DO NOT USE THIS APPLIANCE IF ANY PART HAS BEEN UNDER WATER. IMMEDIATELY CALL A QUALIFIEDSERVICETECHNICIAN TOINSPECTTHEAPPLIANCEAND TO REPLACE ANY PART OF CON- TROL SYSTEM AND ANY GAS CONTROL WHICH HAS BEEN UN- DER WATER.
6) Verify proper operation after servicing.
GLASS
REPLACEMENT
Your Regency stove is supplied with high temperature, 5 mm Neoceram ceramic glass that will withstand the highest heat that your unit will produce. In the event that you break your glass, purchase your replacement from an authorized Regency dealer only, and follow the
Never operate your unit with broken glass.
WARNING: Do not operate appliance with the glass front removed, cracked or bro- ken. Replacement of the glass should be done by a licensed or qualified service person.
heat resistant paint (not with wall paint). |
Regency uses StoveBright Paint - Metallic |
Black #6309. |
3) Make a periodic check of burner for proper |
position and condition. Visually check the |
flame of the burner periodically, making |
sure the flames are steady; not lifting or |
floating. If there is a problem, call a qualified |
service person. |
4) The appliance and venting system must be |
inspected before use, and at least annual- |
ly, by a qualified field service person, to |
ensure that the flow of combustion and |
ventilation air is not obstructed. |
During the annual service call, the burners |
should be removed from the burner tray |
and cleaned. Replace the embers - do not |
block the pilot or burner ports. |
5) Keep the area near the appliance clear and |
free from combustible materials, gasoline |
and other flammable |
vapours and liquids. |
WARNING: CHILDREN AND ADULTSSHOULDBEALERTEDTO THEHAZARDSOFHIGHSURFACE TEMPERATURE AND SHOULD
LOG REPLACEMENT
The unit should never be used with broken logs. Turn off the gas valve and allow the unit to cool before opening door to carefully remove the logs. The pilot light generates enough heat to burn someone. If for any reason a log should need replacement, you must use the proper replacement log. The position of these logs must be as shown in the diagram under Log Installation.
Note: Improper positioning of logs may create carbon
DOOR AND GLASS
GASKET
If the door gasket requires replacement use 7/8" diameter oval door gasket (Part # 650- 920). The glass requires 5/8" flat glass gasket. See your Regency dealer.
MITREDDOOR
Removing Glass:
Note: Wearing gloves will protect your hands while handling glass.
1)Remove the door from the unit and place on a soft surface to prevent scratching.
2)Pull out the door gasket.
3)Remove the 24 nuts holding the glass re- tainers in place. Do not remove the nuts underneath the retainers.
STAYAWAYTOAVOIDBURNSOR CLOTHING IGNITION. YOUNG CHILDRENSHOULDBECAREFUL- LYSUPERVISEDWHENTHEYARE IN THE SAME ROOM AS THE AP- PLIANCE.
CAUTION: ANY SAFETY SCREEN ORGUARDREMOVEDFORSERV- ICING AN APPLIANCE MUST BE REPLACED PRIOR TO OPERAT- ING THE APPLIANCE.
GOLD-PLATED DOORS
The 24 carat gold plated finish on the door requires little maintenance, and need only be cleaned with a damp cloth. DO NOT use abrasive materials or chemical cleaners, as they may harm the finish and will void the warranty. Clean any fingerprints off before turning the unit on.
4)Remove the door catch plate.
5)Remove glass retainers on sides first (3
each side) then remove two center retain- ers.
Note: Center glass retainers are glued to center glass.
6)Remove glass from extrusions. When re- moving center glass, leave white insulation in place.
Regency U38 ULTIMATE Freestanding Gas Heater | 17 |
