0706
HOW TO STEAM CONTINUED…
6. Some garments may react better if they are steamed from the inside.
7. Retailclothingstoresknowtheadvantageofhavingagarmentsteameron
thesalesoor,readyforquicktouchupstomakethegarmentlooklikenew
again. While you can easily store the G4/G4m when not in use (the water
should be drained from the unit if it will be stored for a long period of time)
thebestwaytousethesteamerislikethepros.Haveitinaconvenient
spot where you will use it the most frequently. For some people that would be
intheirlaundryroom,forothersit’sintheirbedroom.BecausetheG4/G4m
heatsupsoquickly(lessthanoneminute)itistheperfectsolutiontotheun-
wearablewrinkledblouseorsweater.Plugitin,turniton,sixtyseconds
laterafewwavesofthesteamheadandyouarelookingyourbest…everyday.
DIRECTIONS FOR USE
TheG4/G4miseasytouse,andeasytosetup.
1. The3-piecerodsetthatholdsupthesteamheadneedstobescrewed
together.Whendone,placetherodsetintothedevicethatholdsitinplace.
2. Withthesuppliedwrench,attachthehosetothebodyofthesteamerand
tighten until it is snug.
3. The same wrench can also be used for tightening the device that holds the
rod set. The steam head can be placed in the upper portion of the rod set until
it is ready for use.
4. Remove the cap from the water bottle. Fill the water bottle with regular tap
ordistilledwater;replacethecapandturninvertthebottle,placing
it in the body of the steamer.
5. Alwaysmakesurethereiswaterinthebottle.DONOTALLOWTHESTEAMERTO
RUNDRY.
6. Turntheuniton,waitforaboutsixtysecondsforthesteamtostart.
7. Itisagoodideatoperiodicallypouroldwateroutofthesteamertoavoid
mineralbuild-up.
NOTE: If rinsing the unit does not improve the performance, the steamer
may require more thorough cleaning. This must be done by an authorized service
center only, or the warranty will be void.
TROUBLESHOOTING
Donotoperatethefabricsteamerwithadamagedcord,plugorifthesteamer
hasbeendroppedordamaged.Toavoidriskofelectricshock,donotdisas-
semble or attempt to repair the unit on your own. Return the unit to Reliable
Corporation(seewarranty)forexamination,repairorreplacement.
PROBLEM
Steamer does not get hot.
The unit is not
producing steam.
Unitproduceslittlesteam
and cycles on/off.
The switch light does not
illuminate when the switch is
turned to the on position.
Water drips from nozzle.
REMEDY
1. Plug the steamer in.
Turn it on.
2. Push the on/off switch to
the off position. Fill the
waterbottleandtitin
place. Turn on.
1. Push the on/off switch to
theoffposition.Rellthe
waterbottleandtitin
place. Turn on.
2. Replace heating element.
1. Throw the old water out
andushtheunit.
2. Replace thermostat.
1. Replace part.
2. Replace part.
3. Replace part.
4. Try plugging into a different
outlet.
1. Hold the hose upright and
allowtodrainbackintothe
base of the unit.
POSSIBLE CAUSES
1. Steam unit is not plugged
in or turned on.
2. Automaticshut-offhas
engaged. The water bottle
is empty and the reservoir
has drained.
1. Water level is too low.
2. Element may not be
functioning.
1. Unitisdirtyandrequires
cleaning.
2. The thermostat may be
defective.
1. Switchisnotworking.
2. Cord is not good.
3. Fuse wire is bad.
4. The outlet may not have
power.
1. Condensation has formed
inside the steamer hose.