Remington Power Tools 106890-01 Storage, Technical Service, Replacement Parts and Accessories

CLEANING AND

MAINTENANCE

Continued

4.Hold file guide level. Make sure 30° mark on file guide is parallel to center of guide bar (see Figure 19). This will insure that you file cutters at 30° angle.

5.File from inside towards outside of cutter until sharp. Only file in this one direction (see Figure 19). Note: Two or three strokes with file should sharpen cutter.

6.After each cutter is sharpened, move chain for- ward to sharpen next cutter. File all cutters on one side of chain.

7.Move to other side of chain and repeat process.

Filing Cutter Depth Gauges

The cutter depth gauge clearance is reduced as cutters are sharpened. After every second or third sharpen- ing, reset cutter depth gauges.

1.Place depth gauge tool (.025") firmly across top of two cutters. Make sure depth gauge enters slot in depth gauge tool (see Figure 21).

2.Use medium flat file. File depth gauge level with depth gauge tool.

3.Remove depth gauge tool. With flat file, round off front corner of cutter depth gauge (see Figure 22).

After several hand filings, have authorized service center or sharpening service machine sharpen chain. This will insure even filing.

REPLACING SAW CHAIN

Replace chain when cutters are too worn to sharpen or when chain breaks. Only use replacement chain noted in this manual. Always include new drive sprocket when replacing chain. This will maintain proper driving of chain. Note: For proper chain and drive sprocket, see

Replacement Parts and Accessories.

STORAGE

If storing saw for more than 30 days, follow steps below.

1.Drain oil tank.

2.Remove and clean guide bar and chain. Clean guide bar and chain by soaking in petroleum based solvent or mild soap and water mixture.

3.Dry guide bar and chain.

4.Place chain in container filled with oil. This will prevent rust.

5.Wipe a thin coating of oil over surface of guide bar.

6.Wipe off outside of saw body. Do this with soft cloth dampened with a mild soap and water mixture.

7.Store chain saw

•in a high or locked place, out of children’s reach

•in a dry place

•in a carrying case or with scabbard over guide bar

TECHNICAL SERVICE

You may have further questions about assembling, operating, or maintaining this product. If so, you can visit our Technical Service web site at www. desatech.com or contact our Technical Service Department at 1-800-858-8501 (English Only). You may also write to:

DESA Specialty Products™ P.O. Box 90004

Bowling Green, KY 42102-9004

ATTN: Technical Service Specialty Products When contacting DESA Specialty Products™, have ready

•Your Name

•Your Address

•Your Phone Number

•Model Number of Product

•Date of Purchase (Include copy of receipt for written requests).

REPLACEMENT PARTS AND ACCESSORIES

WARNING:Useonlyreplacementparts andaccessoriesdescribedinthismanual. Use of other parts or accessories could damage saw or injure operator.

For original replacement parts and accessories, con- tact your nearest Authorized Dealer or Authorized Service Center for this product. If they can not sup- ply the part or accessory, contact your nearest Parts Central listed on page 47. Each Authorized Dealer, Authorized Service Center, and Parts Central is independently owned and operated.

See pages 48 and 49 for an Illustrated Parts List.

If you need additional referral information, contact our Technical Service Department (see Technical Service). In Canada call 1-800-561-3372 for parts information. You may purchase the following service or replace- ment parts:

LNT-2
Part Number	Description
104302-01S#	Guide bar, 8" (20.3 cm)
104301S#	Chain, 8" (20.3 cm)
097567-01S	Guide bar, 10" (25.4 cm)
091371S	Chain, 10" (25.4 cm)
097568-02S	Guide bar, 12" (30.5 cm)
091373-02S	Chain, 12" (30.5 cm)
075752	Drive Sprocket

#Must order both pieces

Continued

108539 21 www.desatech.com